Dell Equallogic Ps6000 recovery: Difference between revisions

From NURDspace
No edit summary
No edit summary
 
(One intermediate revision by the same user not shown)
Line 2: Line 2:
|Name=Dell Equallogic Ps6000 recovery
|Name=Dell Equallogic Ps6000 recovery
|Skills=Computers,
|Skills=Computers,
|Status=Done
|Status=Active
|Niche=Infra
|Niche=Infra
|Purpose=Education
|Purpose=Education
Line 10: Line 10:
|Cost=0
|Cost=0
|Category=Infra
|Category=Infra
|Participants=Rubberduck
}}
}}
1) Console on the Equallogic and powercycle the device
1) Console on the Equallogic and powercycle the device
Line 19: Line 20:
EQL> reload
EQL> reload
And the defaults are back.
And the defaults are back.
Launch Support Mode > support exec bash
To enter a BASH shell > su exec bash
Various “Netstat” and netstat_test commands…some of the most useful networking commands I’ve used so far:
netstat -i
nstat_test -p 0
nstat_test -r
nstat_test -t
“Cache Tool”
cachetool
Reveal NetBSD
uname -a
“RAIDTOOL” for displaying RAID Info, especially useful in watching the rebuilds with percentages
raidtool
Replication Tuning – TCP
support repl-window-size
Restart the Equallogic Management Service (Note: You must close and re-launch the Group Manager application after running these commands)
eqlinit restart MgmtExec
eqlinit restart-snap MgmtExec
support eqlinit “restart MgmtExec”
Check the status od the MgmtExec Service
eqlinit status
DOWN and UP ETH Ports … first select the Array that you want to operate on (the example connects to array JERMSMIT-01, then toggles eth0 off and then on again)
member select JERMSMIT-01
eth select 0 down
eth select 0 up
“UNAME” (unsure what this is actually doing…)
uname -a
Restart the Network Management service
eqlinit restart-snap netmgtd
“PSGD Test”
psgd_test -r
“EQL Logger”
eqllogger -r
“Clear Cache” – The clearlostdata command will gather information about the state of this array for support and troubleshooting purposes.
clearlostdata

Latest revision as of 17:11, 17 October 2022

Dell Equallogic Ps6000 recovery
Participants
Skills Computers
Status Active
Niche Infra
Purpose Education
Tool No
Location @ home
Cost 0
Tool category Infra

Dell Equallogic Ps6000 recovery

/home/arko/Pictures/dell.png {{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost::0 | }}

1) Console on the Equallogic and powercycle the device

2) Press CTRL+P on boot

3) Use the following commands: EQL> setenv RESETPASSWORD 1 EQL> reload And the defaults are back.

Launch Support Mode > support exec bash To enter a BASH shell > su exec bash

Various “Netstat” and netstat_test commands…some of the most useful networking commands I’ve used so far: netstat -i nstat_test -p 0 nstat_test -r nstat_test -t

“Cache Tool” cachetool

Reveal NetBSD uname -a

“RAIDTOOL” for displaying RAID Info, especially useful in watching the rebuilds with percentages raidtool

Replication Tuning – TCP support repl-window-size

Restart the Equallogic Management Service (Note: You must close and re-launch the Group Manager application after running these commands)

eqlinit restart MgmtExec eqlinit restart-snap MgmtExec support eqlinit “restart MgmtExec”

Check the status od the MgmtExec Service eqlinit status

DOWN and UP ETH Ports … first select the Array that you want to operate on (the example connects to array JERMSMIT-01, then toggles eth0 off and then on again) member select JERMSMIT-01 eth select 0 down eth select 0 up

“UNAME” (unsure what this is actually doing…) uname -a

Restart the Network Management service eqlinit restart-snap netmgtd

“PSGD Test” psgd_test -r

“EQL Logger” eqllogger -r

“Clear Cache” – The clearlostdata command will gather information about the state of this array for support and troubleshooting purposes. clearlostdata