LED banner wall: Difference between revisions

From NURDspace
Line 36: Line 36:


=== Source code ===
=== Source code ===
* https://github.com/flok99/BigLedPanel
==== old ====
* https://github.com/NURDspace/BigLedPanel
* https://github.com/NURDspace/BigLedPanel
* https://git.nurdspace.lan/bigledpanel/bigledpanel/ (new location)
* https://git.nurdspace.lan/bigledpanel/bigledpanel/ (new location)
==== old ====
* First try https://gist.github.com/zarya/10f47d6b3097643f4016
* First try https://gist.github.com/zarya/10f47d6b3097643f4016
* It starts to work https://gist.github.com/zarya/33fe46dac38b89f84d60
* It starts to work https://gist.github.com/zarya/33fe46dac38b89f84d60

Revision as of 20:39, 6 July 2019

LED banner wall
2013-07-02 23.08.34.jpg
Participants Bjornl
Skills Programming, electronics, Arduino
Status Operational
Niche Electronics
Purpose Infrastructure
Tool No
Location
Cost
Tool category

LED banner wall

2013-07-02_23.08.34.jpg {{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost::{{{Cost}}} | }}

Small sign

Yotson modified a small LED banner sign to be controlled by an Arduino. After hooking it up to the Dockstar and reprogramming SpaceBot it is now stored somewhere. Code is available on github, based on this earlier code.

15/12/13

Petraea dragged the sign out to give it a little dusting down to find that a bunch of columns no longer worked(See inset animation) BrokenChip.gif A little digging around identified that the CLK line was broken, so a simple extra wire was fitted to repair this.

Left EditedLEDStripBack.jpg


Working.jpg

Large sign

DeDaan brought in a larger sign. This used to work at the previous location.

Current status

Works! There's a beaglebone connected to it. Port 5001 on 10.208.42.176 udp receives text. Root-account is the usual password.

Source code

old

First images

Schema's / Electronics

Arduino Pin setup

PORT_D
 0 (PD0) - UART RX
 1 (PD1) - D5
 2 (PD6) - D3 A0
 3 (PD5) - D4 A1
 4 (PD4) - D6 A2
 5 (PD3) - D2
 6 (PD2) - D0
 7 (PD1) - D1
PORT_B
 8  (PB0) - MR
 9  (PB1) - E1
 10 (PB3) - E2
PORT_C
 14 (A0,PC0) - A0
 15 (A1,PC1) - A1
 16 (A2,PC2) - A2

PIN OUT

01 - VCC
02 - VCC
03 - VCC
04 - SN74LS273N PIN 1 (MR)
05 - SN74LS138N PIN 5 (E2)
06 - SN74LS273N PIN 4 (D1)
07 - SN74LS138N PIN 1 (A0)
08 - SN74LS273N PIN 3 (D0)
09 - SN74LS138N PIN 2 (A1)
10 - SN74LS273N PIN 7 (D2)
11 - SN74LS138N PIN 3 (A2)
12 - SN74LS273N PIN 17 (D6)
13 - SN74LS138N PIN 4 (E1)
14 - SN74LS273N PIN 13 (D4)
15 - GND
16 - SN74LS273N PIN 8 (D3)
17 - GND
18 - SN74LS273N PIN 14 (D5)
19 - GND
20 - GND

Ledboard groot schema.png Ledboard Chip placement.png

Old info

The larger sign contains a separate control unit, programmed using a separate keyboard with a DB-9 like plug. It is attached to a PCB containing the LEDs with a 20 pin flatcable.

The control unit ( http://www.flickr.com/photos/bjornlammers/8425066292/in/photostream ) contains the following ICs:

The Toshiba and the unmarked IC are in a socket, the other two are soldered to the PCB.

The LED panel ( http://www.flickr.com/photos/bjornlammers/8425075284/in/photostream ) contains:

See also this tech-archive thread: http://sci.tech-archive.net/Archive/sci.electronics.repair/2012-06/msg00302.html