Nurd Plotter: Difference between revisions

From NURDspace
No edit summary
No edit summary
Line 26: Line 26:
| SG90 Servo || 1 || - || - || 0 || Can probably source from somewhere
| SG90 Servo || 1 || - || - || 0 || Can probably source from somewhere
|-
|-
| 8mm x 450mm Linear rod || 2 || - || - || ? || Have to figure out where to buy, or maybe the space has two left.
| 8mm x 450mm Linear rod || 2 || 2 || - || - || Got the needed rods that are slightly longer
|-
|-
| 3mm x 100mm Linear rod || 2 || - || - || ? || Have to figure out where to buy, or maybe the space has two left.
| 8mm x 350mm Linear rod || 2 || 2 || - || - || Got the needed rods that are slightly longer
|-
|-
| LM8UU linear bearings || 8 || - || - || - || -
| 3mm x 100mm Linear rod || 2 ||  - || - || ? || Got one so far from a CD drive
|-
| LM8UU linear bearings || 8 || 4 || - || - || Got 4 so far, need 4 more!
|-
|-
| 2 Meter GT2 Timing Belt || 1 || -  || https://www.aliexpress.com/item/1005001469085218.html || €0,73 || -
| 2 Meter GT2 Timing Belt || 1 || -  || https://www.aliexpress.com/item/1005001469085218.html || €0,73 || -
|-
|-
| 4mmx13mmx5mm ball bearings || 10 || -  || - || - || -
| 4mmx13mmx5mm ball bearings || 10 || -  || - || - || -
|-
|-
| 40mm cooling fan  || 2 || -  || https://www.aliexpress.com/item/1005003663915828.html || 2x €4,71 || I want to go with PWM controlled fans
| 40mm cooling fan  || 2 || -  || https://www.aliexpress.com/item/1005003663915828.html || 2x €4,71 || I want to go with PWM controlled fans
Line 40: Line 42:
| Nema 17 Bipolar 40mm 64oz.in(45Ncm) 2A stepper || 2 || -  || https://www.tinytronics.nl/shop/nl/mechanica-en-actuatoren/motoren/stappenmotoren/stappenmotor-dubbelzijdige-as-0.41n.m-1.7a-nema17-jst-ph-connector || 2x €11,50 || Assuming we can also go with one that is a slightly lower ampere
| Nema 17 Bipolar 40mm 64oz.in(45Ncm) 2A stepper || 2 || -  || https://www.tinytronics.nl/shop/nl/mechanica-en-actuatoren/motoren/stappenmotoren/stappenmotor-dubbelzijdige-as-0.41n.m-1.7a-nema17-jst-ph-connector || 2x €11,50 || Assuming we can also go with one that is a slightly lower ampere
|-
|-
| A3967 EasyDriver || 2  || - || https://www.aliexpress.com/item/4000200930571.html|| 2x €2,31 || We could probably also go with different drivers, if they fit.
| A3967 EasyDriver || 2  || - || https://www.aliexpress.com/item/4000200930571.html|| 2x €2,31 || Ordered 2!
|-
|-
| Heatsinks || 2 || - || https://www.aliexpress.com/item/32817339178.html || €1,66 || Comes in a 4 pack  
| Heatsinks || 2 || - || https://www.aliexpress.com/item/32817339178.html || €1,66 || Comes in a 4 pack  
Line 50: Line 52:
| M4 x 0.7mm 304 lock nuts || 50 || - || - || -
| M4 x 0.7mm 304 lock nuts || 50 || - || - || -
|-
|-
| M4x10mm thumb screws || 15 || - || - || -
| M4 x 10mm thumb screws || 15 || - || - || -
|}
|}



Revision as of 20:39, 22 April 2022

Nurd Plotter
NoPicture.png
Participants
Skills
Status Active
Niche Artsy stuff
Purpose Tool
Tool No
Location
Cost
Tool category Fabrication

Nurd Plotter Property "Tool Image" (as page type) with input value "File:{{{Picture}}}" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process. {{{Picture}}} {{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost::{{{Cost}}} | }}

To teach myself more about electronics, as well as to finally step into the world of stepper-motors I would like to try to make a plotter. Since I don't know enough yet to completely design one from scratch, it will be build after Ben's PlottyBot as he did an excellent write-up on how he did his. It also has limiter-switches for homing and a servo that can move the pencil up and down, as well as an adjustable pen holder.

Right now this project is still in an "can I?" and "sourcing parts" state.

Nurdplotter 3dview.png

Parts

Note: I'm not including the raspberry pi zero in the part list because I still have one laying around.

Item Units State Link Price Remarks
12V power supply 1 - - 0 Sourcing this part isn't an issue. 2~3A seems to be enough.
5v regulator 1 - - 0 Should have a couple laying around
SG90 Servo 1 - - 0 Can probably source from somewhere
8mm x 450mm Linear rod 2 2 - - Got the needed rods that are slightly longer
8mm x 350mm Linear rod 2 2 - - Got the needed rods that are slightly longer
3mm x 100mm Linear rod 2 - - ? Got one so far from a CD drive
LM8UU linear bearings 8 4 - - Got 4 so far, need 4 more!
2 Meter GT2 Timing Belt 1 - https://www.aliexpress.com/item/1005001469085218.html €0,73 -
4mmx13mmx5mm ball bearings 10 - - - -
40mm cooling fan 2 - https://www.aliexpress.com/item/1005003663915828.html 2x €4,71 I want to go with PWM controlled fans
Nema 17 Bipolar 40mm 64oz.in(45Ncm) 2A stepper 2 - https://www.tinytronics.nl/shop/nl/mechanica-en-actuatoren/motoren/stappenmotoren/stappenmotor-dubbelzijdige-as-0.41n.m-1.7a-nema17-jst-ph-connector 2x €11,50 Assuming we can also go with one that is a slightly lower ampere
A3967 EasyDriver 2 - https://www.aliexpress.com/item/4000200930571.html 2x €2,31 Ordered 2!
Heatsinks 2 - https://www.aliexpress.com/item/32817339178.html €1,66 Comes in a 4 pack
Rubber Feet 14 - - - Can probably buy them at the Action
M4 flat washers inside: 4.3m, item: 9m thickness: 0.8m 50 - - -
M4 x 0.7mm 304 lock nuts 50 - - -
M4 x 10mm thumb screws 15 - - -

Probably is incomplete and or need more parts to be bought.

Resources

- https://ben.akrin.com/plottybot/

- https://www.youtube.com/watch?v=LUbhPKBL_IU