Difference between revisions of "PLCC32 in Circuit flash/eeprom Programmer"

From NURDspace

Jump to: navigation, search
(Created page with "== Goal == Being able to program PLCC32 chips while they remain soldered to the board. The chips are commonly found in a wide range of equipment, including PC motherboards. ...")
 
m (Text replacement - "ProjectPurpose=" to "Purpose=")
 
(7 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 +
{{Project
 +
|Skills=Electronics, Programming
 +
|Status=Planning
 +
|Niche=Electronics
 +
|Purpose=Use in other project
 +
}}
 
== Goal ==
 
== Goal ==
 
Being able to program PLCC32 chips while they remain soldered to the board. The chips are commonly found in a wide range of equipment, including PC motherboards.
 
Being able to program PLCC32 chips while they remain soldered to the board. The chips are commonly found in a wide range of equipment, including PC motherboards.
[[File:2014-06-14 18.57.40.jpg|thumb|400px|PLCC32 chip soldered on motherboard holding the BIOS]]
+
 
 +
<gallery>
 +
Image:2014-06-14 18.57.40.jpg|PLCC32 chip soldered on motherboard holding the BIOS
 +
</gallery>
 +
 
  
 
== Connector ==
 
== Connector ==
 
They can be bought online but are quite expensive, for instance on http://www.hmcelectronics.com/product/Pomona/5733. I do however own a PLCC32 to DIP32 converter. I tried to put a PLCC32 chip in there upside down. When you apply some pressure, all pins seem to connect nicely. Then the idea was born to just use a PLCC32 socket and solder some wires to it to connect it to a programmer.
 
They can be bought online but are quite expensive, for instance on http://www.hmcelectronics.com/product/Pomona/5733. I do however own a PLCC32 to DIP32 converter. I tried to put a PLCC32 chip in there upside down. When you apply some pressure, all pins seem to connect nicely. Then the idea was born to just use a PLCC32 socket and solder some wires to it to connect it to a programmer.
[[File:2014-06-14 18.57.17.jpg|thumb|400px|PLCC32 to DIP32 converter]]
+
 
 +
<gallery>
 +
Image:2014-06-14 18.57.17.jpg|PLCC32 to DIP32 converter
 +
</gallery>
  
 
== Programmers ==
 
== Programmers ==

Latest revision as of 11:04, 25 August 2014

NURDspace Project
link=File:{{{Name}}}.jpg
Participants Dennis
Skills Electronics, Programming
Status Planning
Niche Electronics
Purpose Use in other project
Tool
Location
Cost
Tool category
{{{Name}}}
"{{{Name}}}" cannot be used as a page name in this wiki.
"File:{{{Picture}}}" cannot be used as a page name in this wiki.

{{{Picture}}} {{#if:{{{Tool}}} | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:{{{Tool}}} | [[Tool Cost::{{{Cost}}} | }}

Goal

Being able to program PLCC32 chips while they remain soldered to the board. The chips are commonly found in a wide range of equipment, including PC motherboards.


Connector

They can be bought online but are quite expensive, for instance on http://www.hmcelectronics.com/product/Pomona/5733. I do however own a PLCC32 to DIP32 converter. I tried to put a PLCC32 chip in there upside down. When you apply some pressure, all pins seem to connect nicely. Then the idea was born to just use a PLCC32 socket and solder some wires to it to connect it to a programmer.

Programmers

 
Our site is hosted by Site4U
Site4U
Our connectivity is made available by BIT
To BIT's website