Difference between revisions of "Pokons to do list"

From NURDspace

Jump to: navigation, search
(Created page with "{{Project |Name=Pokons printer to do list |Status=Planning |Niche=Documentation |Purpose=Infra |Tool=Yes |Location=everywhere where there is a printer |Cost=dont know dont car...")
 
Line 9: Line 9:
 
|Category=Electronics
 
|Category=Electronics
 
}}
 
}}
Anet a8 stock
+
== Anet a8 stock ==
-Resolder wires from the board to the mosfet
+
-PID tune so it wont overshoot about 50 degrees
+
-check filament gear because of grinding
+
-Level the bed once again
+
  
Malyan m200 Modded
+
* Resolder wires from the board to the mosfet
-write the marlin config
+
* PID tune so it wont overshoot about 50 degrees
-level the bed
+
* check filament gear because of grinding
-PID tune
+
* Level the bed once again
-get a glass bed and relevel again
+
  
Super metal space printer (aka anet but with extrusions)
+
== Malyan m200 Modded ==
-wire the electronics
+
* write the marlin config
-get a mosfet for the bed
+
* level the bed
-PID tune  
+
* PID tune
-Level the bed
+
* get a glass bed and relevel again
-testprint
+
-make a cura profile
+
-hook it up to octoprint
+
-make a manual so that every nurd can use it
+
  
Envisiontec printer
+
== Super metal space printer (aka anet but with extrusions) ==
-poke envisiontec again  
+
* wire the electronics
-poke around in the community for an opensource alternative
+
* get a mosfet for the bed
 +
* PID tune
 +
* Level the bed
 +
* testprint
 +
* make a cura profile
 +
* hook it up to octoprint
 +
* make a manual so that every nurd can use it
 +
 
 +
== Envisiontec printer ==
 +
* poke envisiontec again  
 +
* give buzz the backup finally so he can get the software hacked
 +
* poke around in the community for an opensource alternative

Revision as of 16:07, 5 August 2018

Pokons printer to do list
NoPicture.png
Participants
Skills
Status Planning
Niche Documentation
Purpose Infra
Tool Yes
Location everywhere where there is a printer
Cost dont know dont care
Tool category Electronics

Pokons printer to do list

"File:{{{Picture}}}" cannot be used as a page name in this wiki.

{{{Picture}}} {{#if:Yes | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:Yes | [[Tool Cost::dont know dont care | }}

Anet a8 stock

  • Resolder wires from the board to the mosfet
  • PID tune so it wont overshoot about 50 degrees
  • check filament gear because of grinding
  • Level the bed once again

Malyan m200 Modded

  • write the marlin config
  • level the bed
  • PID tune
  • get a glass bed and relevel again

Super metal space printer (aka anet but with extrusions)

  • wire the electronics
  • get a mosfet for the bed
  • PID tune
  • Level the bed
  • testprint
  • make a cura profile
  • hook it up to octoprint
  • make a manual so that every nurd can use it

Envisiontec printer

  • poke envisiontec again
  • give buzz the backup finally so he can get the software hacked
  • poke around in the community for an opensource alternative
 
Our site is hosted by Site4U
Site4U
Our connectivity is made available by BIT
To BIT's website