ScarlettScroller: Difference between revisions

From NURDspace
No edit summary
Line 1: Line 1:
{{Project
|Name=Scarlett Scroller
|Skills=Hacking, Electronics, Programming, making, lights,
|Status=Active
|Niche=Artsy stuff
|Purpose=Fun
|Picture=
|Tool=Yes
|Location=Zaal1
|Category=Electronics
}}
[[File:ScarlettScroller.gif|right|Scarlett Scroller]]
[[File:ScarlettScroller.gif|right|Scarlett Scroller]]



Revision as of 22:32, 19 April 2022

Scarlett Scroller
NoPicture.png
Participants
Skills Hacking, Electronics, Programming, making, lights
Status Active
Niche Artsy stuff
Purpose Fun
Tool Yes
Location Zaal1
Cost
Tool category Electronics

Scarlett Scroller Property "Tool Image" (as page type) with input value "File:" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process.

{{#if:Yes | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:Yes | [[Tool Cost::{{{Cost}}} | }}


Scarlett Scroller

For questions about this project, see User:Bertrik on how to contact me.

This page is about modifying a 80x7 pixel scrolling red LED sign with an alternative controller (ESP8266) running custom firmware. This makes it possible to use the LED sign as a networked display (WiFi), with pixels that can be individually dimmed in 255 levels.

Hardware

The model number is AM03127.

It has 16 elements of 5x7 red LEDs each, for a total of 80x7 LEDs. This particular board has monochrome LEDs only.

The electronics consist of two boards: a controller board and a LED board.

The LED board has the following ICs:

  • SN74HC138: 3-to-8 line decoder/multiplexer
  • SN74HC04: 6 inverters
  • 10x SN74HC164: 8-bit parallel-out serial shift registers
  • 4x APM4953: dual P-Channel Enhancement Mode Mosfet

The boards are connected through a 10 pin connector and a 5V power connector.

Control connector

Lichtkrant connector

Pinout:

  • pin 1: SCLK
  • pin 2: SCLK (shorted to pin 1)
  • pin 3: G = 'green' data bit shifted into row, goes through inverter 6
  • pin 4: R = 'red' data bit, goes through inverter 1
  • pin 5: A = row select LSB
  • pin 6: B = row select
  • pin 7: C = row select MSB
  • pin 8: D = appears to not be connected to anything
  • pin 9: GND
  • pin 10: GND
JP7
SCLK SCLK
R G
B A
D C
GND GND

(as viewed on the controller board)

JP1
GND D B R SCLK
GND C A G SCLK

(as viewed from the back side)


Unfortunately the connector does not seem to carry 5V. If that were the case, a replacement microcontroller could be powered directly from the connector, with the main power entering through the 5V power plug.

The display can be blanked by selecting row 0, e.g. signals A, B and C all 0.

Power

The control board is powered by a 12V supply and probably contains a step-down converter to turn it into 5V internally.

Theory of operation

There are 80 pixels horizontally and 10 serial-parallel chips with 8 outputs each, so one row of pixels can be kept in the shift registers.

The 3-to-8 decoder selects one particular row to light, through pins A/B/C. The MOSFETs are used as drivers. Selecting row 0 (A, B, C all 0) disables the display, i.e. does not light any row.

The SCLK signal goes to the CLK input of all serial-parallel SN74HC164 chips.

The LED board is prepared to be used with R+G LED modules, however this particular board does not have the shift register populated for the dual-color.

It appears there is no 'latch' signal, although the controller board has the text 'LAT'. A latch signal could activate the row data after it's been written to the shift registers, thereby avoiding the pixels showing up already as they're being written and reducing the contrast.

Firmware

Github archive: https://github.com/bertrik/scarlettscroller

The firmware run this on an ESP8266 (wemos d1 mini), which is connected to the LED board through dupont-wire.

The firmware connects to the local wifi network (sets up a captive portal when no wifi has been configured yet). Then the framebuffer can be accessed over UDP port 8888. Just send a UDP frame consisting of 80x7 bytes, each byte representing a brightness.


network

On 10.208.42.159 port 5108 listens for UDP pixelflood (text!). Port 5120 (also UDP) listens for text messages.


Scarlettscroller.jpg