Space anet a8: Difference between revisions

From NURDspace
(Created page with "{{Project |Name=Anet a8 for space |Skills=pokoning, 3D Printing, screaming, |Status=Active |Niche=Printing |Purpose=Electronics, fun, world domination |Tool=No |Location=with...")
 
(11 intermediate revisions by 2 users not shown)
Line 5: Line 5:
|Niche=Printing
|Niche=Printing
|Purpose=Electronics, fun, world domination
|Purpose=Electronics, fun, world domination
|Tool=No
|Picture=Anet a8.jpg
|Tool=Yes
|Location=with the rest of the printers
|Location=with the rest of the printers
|Cost=120 ish
|Cost=120 ish
|Category=Electronics
|Category=Fabrication
}}
}}
== What ==
So another day another 3d printer  
So another day another 3d printer  


this time its the anet a8 from el cheapo land gearbest
this time its the anet a8 from el cheapo land gearbest
below you will find the profile settings for cura 2.6.2
below you will find the profile settings for cura 2.6.2
*http://space.nurdspace.nl/~pokon/
== Needed upgrades ==
*New PSU (the one that came with is a fire hazard)
*Mosfet (board of the printer cant handle the amps directly)
https://www.aliexpress.com/item/3D-Printer-Parts-General-Add-on-Heated-Bed-Power-Expansion-Module-High-Power-Module-expansion-board/32765683570.html?spm=a2g0s.9042311.0.0.b522U7
*putting spades on the cables from the psu and heatbed
*replace heatbed wire for thicker ones (the cables from a eurostekker are suffecient)
*solder the wires directly on the headbed (connector is a fun fire hazard)
== Printed upgrades ==
*x tensioner
*https://www.thingiverse.com/thing:1492411
*y tensioner
*same as the x one 2 files in one :)
*frame thing stabalizer
*https://www.thingiverse.com/thing:1672959
*fan duct (best not to print in pla because of meltyness)
*https://www.thingiverse.com/thing:2133328


upgrades wich are needed:
The printer will be eventually be fully upgraded to a AM8
*https://www.thingiverse.com/thing:2263216


New PSU (the one that came with is a fire hazard)
== Todo list ==
Mosfet (board of the printer cant handle the amps directly)
*build manual so other people can print with
*place the links for the 3d printed upgrades
*upgrade the printer to said AM8 frame


printed upgrades (links will be added):
== How to avoid temp overshoot issue ==
x tensioner
First set temp via display menu. Then print from sd card.
y tensioner
frame thing stabalizer
fan duct (best not to print in pla because of melty)

Revision as of 16:43, 7 December 2018

Anet a8 for space
Anet a8.jpg
Participants
Skills pokoning, 3D Printing, screaming
Status Active
Niche Printing
Purpose Electronics, fun, world domination
Tool Yes
Location with the rest of the printers
Cost 120 ish
Tool category Fabrication

Anet a8 for space

Anet a8.jpg {{#if:Yes | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:Yes | [[Tool Cost::120 ish | }}

What

So another day another 3d printer

this time its the anet a8 from el cheapo land gearbest

below you will find the profile settings for cura 2.6.2

Needed upgrades

  • New PSU (the one that came with is a fire hazard)
  • Mosfet (board of the printer cant handle the amps directly)

https://www.aliexpress.com/item/3D-Printer-Parts-General-Add-on-Heated-Bed-Power-Expansion-Module-High-Power-Module-expansion-board/32765683570.html?spm=a2g0s.9042311.0.0.b522U7

  • putting spades on the cables from the psu and heatbed
  • replace heatbed wire for thicker ones (the cables from a eurostekker are suffecient)
  • solder the wires directly on the headbed (connector is a fun fire hazard)


Printed upgrades

The printer will be eventually be fully upgraded to a AM8

Todo list

  • build manual so other people can print with
  • place the links for the 3d printed upgrades
  • upgrade the printer to said AM8 frame

How to avoid temp overshoot issue

First set temp via display menu. Then print from sd card.