3D-Print Farm: Difference between revisions

From NURDspace
(Created page with "{{Project |Name=3D-Print Farm |Status=Operational |Niche=3D Printing |Purpose=Reliable fabrication |Picture=3d-Print Farm.jpeg |Tool=Yes |Location=3D-Corner |Category=Fabrication }} Printserver is available at http://10.208.1.19/ or http://http://nurds3d.lan.nurd.space/. We try to keep an array of working printers connected to this server. Current printers: * Ultimaker Original (3mm) * Ultimaker Original + (3mm) * Creality Ender-3 V2 (1.75mm) Limitations: *...")
 
No edit summary
 
(6 intermediate revisions by 2 users not shown)
Line 9: Line 9:
|Category=Fabrication
|Category=Fabrication
}}
}}
Printserver is available at http://10.208.1.19/ or http://http://nurds3d.lan.nurd.space/.
Printserver is available at http://10.208.1.19/ or http://nurds3d.lan.nurd.space/.


We try to keep an array of working printers connected to this server.
We try to keep an array of working printers connected to this server.
Line 23: Line 23:
Upgrade plans:
Upgrade plans:
* Replace hotend in Ultimaker Original (+) with E3DV6
* Replace hotend in Ultimaker Original (+) with E3DV6
* Replace Ultimaker extruders with E3D
* Replace Ultimaker extruders with E3D Titan
We recommend using PrusaSlic3r. Printer profiles to follow ...
 
'''IMPORTANT NOTE: both Ultimakers have custom firmware because pins were not working and a pinswap in the firmware was necessary.'''
* Ultimaker Original: Y-axis (IIRC) step and dir swapped to spare driver position.
* Ultimaker Original +: cooling fan was not working properly. swapped with pwm-output of LEDs. Hopefully fixed soon by replacing transistor.
 
 
We recommend using PrusaSlic3r to convert STL to gcode, then upload gcode to the appropriate printer on the server and print. Printer profiles to follow ...
 
 
 
FvH says: PrusaSlicer does not seem to support the Ultimaker? For the ultimaker, you can use https://ultimaker.com/software/ultimaker-cura/

Latest revision as of 16:40, 7 September 2024

3D-Print Farm
3d-Print Farm.jpeg
Participants
Skills
Status Operational
Niche 3D Printing
Purpose Reliable fabrication
Tool Yes
Location 3D-Corner
Cost
Tool category Fabrication

3D-Print Farm

3d-Print Farm.jpeg {{#if:Yes | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:Yes | [[Tool Cost::{{{Cost}}} | }}

Printserver is available at http://10.208.1.19/ or http://nurds3d.lan.nurd.space/.

We try to keep an array of working printers connected to this server.

Current printers:

  • Ultimaker Original (3mm)
  • Ultimaker Original + (3mm)
  • Creality Ender-3 V2 (1.75mm)

Limitations:

  • Ultimaker Original (+) are prone to heat-creep with the combination of higher temperature filaments, frequent retractions/low-flow conditions.

Upgrade plans:

  • Replace hotend in Ultimaker Original (+) with E3DV6
  • Replace Ultimaker extruders with E3D Titan

IMPORTANT NOTE: both Ultimakers have custom firmware because pins were not working and a pinswap in the firmware was necessary.

  • Ultimaker Original: Y-axis (IIRC) step and dir swapped to spare driver position.
  • Ultimaker Original +: cooling fan was not working properly. swapped with pwm-output of LEDs. Hopefully fixed soon by replacing transistor.


We recommend using PrusaSlic3r to convert STL to gcode, then upload gcode to the appropriate printer on the server and print. Printer profiles to follow ...


FvH says: PrusaSlicer does not seem to support the Ultimaker? For the ultimaker, you can use https://ultimaker.com/software/ultimaker-cura/