|
|
| Line 32: |
Line 32: |
| screen /dev/ttyACM0 115200 | | screen /dev/ttyACM0 115200 |
|
| |
|
| ==== forwarder setup ==== | | ==== Forwarder setup ==== |
| When running 'opkg upgrade', it logged the following:
| | The gateway was fully re-installed, by flashing an entirely new image. |
| <pre>
| | Configuration can be done through the web interface (no CLI required). |
| noldus-lorix-one:~$ sudo opkg upgrade
| |
| Configuring packet-forwarder.
| |
| Updating configuration files with gateway ID, type EU868
| |
| ******************************************************************************************
| |
| Default global_conf.json file created from 4dBi outdoor antenna by default,
| |
| don't forget to chose the one corresponding to your antenna using the following command:
| |
| sudo cp /opt/lorix/cloud/ttn/global_conf_<antenna>.json global_conf.json
| |
| ******************************************************************************************
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/packet-forwarder/global_conf.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/packet-forwarder/global_conf_2dBi_indoor.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/packet-forwarder/global_conf_4dBi_outdoor.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/packet-forwarder/local_conf.json
| |
| System startup links for /etc/init.d/packet-forwarder-gw already exist.
| |
| Configuring ttn-packet-forwarder.
| |
| Updating configuration files with gateway ID, type EU868
| |
| ******************************************************************************************
| |
| Default global_conf.json file created from 4dBi outdoor antenna by default,
| |
| don't forget to chose the one corresponding to your antenna using the following command:
| |
| sudo cp /opt/lorix/cloud/ttn/global_conf_<antenna>.json global_conf.json
| |
| ******************************************************************************************
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/ttn/global_conf.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/ttn/global_conf_2dBi_indoor.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/ttn/global_conf_4dBi_outdoor.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/ttn/local_conf.json
| |
| System startup links for /etc/init.d/ttn-gw already exist.
| |
| Configuring loriot.
| |
| System startup links for /etc/init.d/loriot-gw already exist.
| |
| Configuring clouds-manager.
| |
| System startup links for /etc/init.d/init-clouds-manager already exist.
| |
| Stopping cloud loriot... done.
| |
| Starting cloud loriot... done.
| |
| Configuring lora-gateway.
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/utils/global_conf.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/utils/local_conf.json
| |
| Configuring factory-reset.
| |
| System startup links for /etc/init.d/factory-reset.sh already exist.
| |
| Configuring kersing-packet-forwarder.
| |
| Updating configuration files with gateway ID, type EU868
| |
| ******************************************************************************************
| |
| Default global_conf.json file created from 4dBi outdoor antenna by default,
| |
| don't forget to chose the one corresponding to your antenna using the following command:
| |
| sudo cp /opt/lorix/cloud/mp-pkt-fwd/global_conf_<antenna>.json global_conf.json
| |
| ******************************************************************************************
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/mp-pkt-fwd/global_conf.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/mp-pkt-fwd/global_conf_2dBi_indoor.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/mp-pkt-fwd/global_conf_4dBi_outdoor.json
| |
| Gateway_ID set to fcc23dFFFE0f3a24 in file /opt/lorix/clouds/mp-pkt-fwd/local_conf.json
| |
| System startup links for /etc/init.d/mp-pkt-fwd-gw already exist.
| |
| noldus-lorix-one:~$
| |
| </pre>
| |
Intro
NurdSpace has a LorixOne LoRaWAN gateway.
This page is about setting it up for TheThingsNetwork.
More info:
Logging in: go to http://lorix-one-0f3a24.local
Username: admin, password: <SECRET>
Hardware
There's a sticker on the outside:
FC:C2:3D:0F:3A:24 v1.0d
This means it's the 256 MB flash version.
You can screw off the bottom, to reveal an ethernet port and an USB-B port.
It gets power from the power-over-ethernet cable.
Software
Configuration
Network connection (easiest)
The thing does DHCP, and is reachable at
lorix-one-0f3a24.local
e.g. http://lorix-one-0f3a24.local for the web interface
Serial connection (fallback)
Connect a USB A-to-B cable to the USB-B port.
Open a serial terminal at 115200 bits to /tty/ACM0 (typically)
screen /dev/ttyACM0 115200
Forwarder setup
The gateway was fully re-installed, by flashing an entirely new image.
Configuration can be done through the web interface (no CLI required).