NurdNode

NurdNode
Participants
Skills	Electronics, Programming
Status	Planning
Niche	Electronics
Purpose	Fun
Tool	No
Location
Cost
Tool category

NurdNode Property "Tool Image" (as page type) with input value "File:" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process.

{{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost:: | }}

Description

The goal is to build wireless nodes that will control a bunch of LED's for cool lighting effects. The ultimate cool is to build enough, so we can put them in the connector pieces of our geodesic dome

Hardware design considerations

1 node will draw around 1A in current. For 31 nodes, this is obvisouly 31A in current at 5V, making the total power consumption 155W at full load. The current proposition is to bundle the power and signal lines into one cable, and run them in an upward spiraling fashion across each node, connecting them serially. The benefit of this setup is that it allows for easy addressing and it's simple. However, running 31A through a single power line requires a big, heavy and expensive cable.

The length of the power lines is determined at 60m. According to this site [1], at 3% acceptable loss, and using 5V at 31A the cable crossection is 16m2. A ballpark price estimate using Eijlander as supplier is roughly 330 euro.

An alternative would be to devide the power distribution into several groups. The upside is that we can get away with thinner cables, but we may require longer cables.

Yet another alternative is to raise the voltage of the grid to 12+V. This means we may use thinner power lines and still use the serial wiring setup. However, each node will have to be equipped with a switching power source to keep power dissipation at its lowest. This circuit will come at an extra cost, and having 31 nodes, this could escalate quickly.

(Why not elevate voltage a lot more, say 48V? Would reduce the current by an order of magnitude without adding more parts. Talloak (talk) 00:44, 4 May 2015 (CEST) )

Parts selection

IRL540 for power led stages?

TODO

Hardware

• Calulate total length of cable required to connect all nodes
• Calculate price of power lines
• Design power circuit
• Design LED circuit (for optional leds)
• Design power stage for 3W led
• Select appropriate through-hole parts for breadboarding
• Order thru-hole parts
• Build thingamagic on breadboard
• Select appropriate SMD parts for the final device.
  • Select decoupling caps
  • Select connectors
  • Select N-channel MOSFET
  • Select P-channel MOSFET
• Design board
• Assemble BOM
• Determine pinout of PSU
• Create pinout of prototype node
• Build first prototype
• Test first prototype
• Build other prototypes
• Test out smaller FET as replacement for the fat bastards
• Fix design mistakes
• Finalise design
• Order PCB's
• Order metal framed stencil
• Create building instructions
• Equip 10 LEDs with wiring for prototyping purposes
• Build device that will zero in the Servo's
• Build device that tests a LED.
• Equip remaining 90 LED's with wiring
• Assemble 100 Pro mini's
• Assemble remaining 50 PSU's
• Assemble remaining 9 prototypes
• Assemble remaining 90 nodes

Cabling

• Determine guage of power cables
• Determine which signal wires to use
• Order more molex connectors
• Get wires at ijlander, or order
• Build cable

Total cable length based on 10M dome = 31 - 1 * 2m = 60m
Eijlander supples 16mm2 wire [2] for 334.80E for 120m (+ and -).

Ordering

• 100 pcs 3W Led
• 100 pcs PSU
• 100 Pro mini's
• 200 Servos
• 100 Lenses
• 110 Jumper cables for soldering to LED
• 3x solder paste
• Prototype Stencil
• Prototype PCB's
• Enough material for prototypes
• Metal framed stencil for final design
• Final PCB's
• More molex connectors
• Enough materials for final nodes

Software

• Create some spiffy code to make the blinkenlichten go blink blink.
• Create a C&C lib that organises the nodes and takes care of the comms between the nodes and the higher level software. I'm thinking REST API for the higher level stuff and UDP multicast for the lower end. Suggestions welcome.
• Find a tool (better yet DIY) a tool that allows you to define an animation in 3D and project it on the geodome.

Links

• Potential 24V power supply: http://www.ebay.com/itm/321660472921
• Or 48V?: http://www.ebay.com/itm/261847060063
• Step down from 24V: http://www.ebay.com/itm/171381728637
• Leds: http://www.ebay.com/itm/191388798412
• Or: http://www.ebay.com/itm/221544924178 with added heatsinks onboard.
• Extra heatsinkery: http://www.ebay.com/itm/331286129263
• Sticky pads for connection: http://www.ebay.com/itm/121331880334

• Interesting source of servo's: http://www.giantshark.co.uk/product/167511/towerpro-sg90-9g-micro-servo - with returns in the UK. Promising!

• Rectifier: https://www.fairchildsemi.com/datasheets/ES/ES1A.pdf
• XT60 conns: http://www.ebay.nl/itm/100pcs-50-pairs-XT60-Plug-Connector-Heat-Shrink-for-RC-Airplane-Quadcopter-DIY-/261863841242
• ATX PSU Molex types: http://www.overclock.net/t/1136451/molex-atx-power-supply-connectors-and-part-numbers