Picknplacer: Difference between revisions

From NURDspace
 
(132 intermediate revisions by 3 users not shown)
Line 5: Line 5:
|Niche=Hardware
|Niche=Hardware
|Purpose=Instrument
|Purpose=Instrument
|Picture=Picknplace-20160626.png
|Tool=Yes
|Tool=Yes
|Location=Nurdspace
|Location=Nurdspace
Line 14: Line 15:
In order to produce many part prototypes, or make large productions runs, an automatic pick and place machine is imperative.
In order to produce many part prototypes, or make large productions runs, an automatic pick and place machine is imperative.


= Design =
== Parts (unspecific) ==
{| class="wikitable"
| [http://shop.myhobby-cnc.de/bauteile/mechanische-bauteile/profile/2/makerslide-natur?c=17 makerslide] || xlots || 0.02 EUR
|-
| [http://us.misumi-ec.com/item/10300438140/img/drw_01.gif HBLTSW5] brackets  || 5x ||??
|-
| [https://www.inventables.com/technologies/dual-bearing-v-wheel-kit V-wheel] || ?x || ??
|-
| [http://www.ebay.com/itm/252006568725 603VV] || ||
|-
| [http://www.ebay.co.uk/itm/321674612203 screws?] || ||
|-
| [http://www.ebay.com/itm/182055223170 T slot bolts] || ||
|-
| [https://www.inventables.com/technologies/smooth-idler-wheel-kit idler wheels] || ||
|-
| [http://www.ebay.com/itm/311569895148 cameras] || x2 || $13.05
|}
== PNP Head ==
{| class="wikitable"
| PnP head middle plate || x1
|-
| PnP head lower plate || x1
|-
| Nema14 rotation stepper motor (14HM08-0504S) [http://www.ebay.com/itm/262351980331 ?]  || x1
|-
| M3-8 || x 4
|-
| M3 washer  || x 14
|-
| M3 nut || x 5
|-
| M3x6 || x 5
|-
| M3 extrusion nut || x 2
|-
| M3-20 || x2
|-
| M4 nut (not M3) || x?
|-
| M5-12 bolt || x 2
|-
| M5 washer || x 11
|-
| M5 nut || x 2
|-
| M5-8 || x?
|-
| M5-10 bolt || x 2
|-
| M5 extrusion nut || x 3
|-
| HTJ5 screw || x 2
|-
| * [http://www.ebay.com/itm/261897151126 linear flanged bearing]
* [http://uk.misumi-ec.com/vona2/detail/110302581540/?HissuCode=C-LHFC8 LHFC8 bearing] || x 2
|-
| [http://uk.misumi-ec.com/item/10300438930/img/drw_01.gif HBLSD5 bracket] [http://www.ebay.com/itm/351634181791 ?] || x 1
|-
| [http://uk.misumi-ec.com/item/10300438930/img/drw_01.gif HBLSS5 bracket] [http://www.ebay.com/itm/391273058496 ?]  [http://www.ebay.com/itm/121121527338 ??] || x1
|-
| MakerSlide || 250mm
|-
| Pick-up tube || x1
|-
| [http://www.ebay.com/itm/291616892218 M8 nylon washer] || x 3
|-
| GT2-36 pulley || x1
|-
| GT2-60 belt loop || x1
|-
| [http://www.ebay.com/itm/161505879476 SCCN8-6 collar] x 1
|-
| [http://www.ebay.com/itm/231319673678 spring]  || x1
|-
| [http://http://www.ebay.com/itm/191248998291 Omron D3V-162-1C4 limit switch] ||2x
|-
| WSSB12-3-1 washer || 1x
|-
| Flat spring || 1x
|}
== X frame ==
=== Parts ===
* 20x20x767 alu extrusion
* M5-10
* M5 washer x 10
* M5-15 x 2
* M5 nut x 3
* M5-12
* M5 extrusion nut
* [http://uk.misumi-ec.com/item/10300438930/img/drw_01.gif HBLSS5] bracket x2
* 140mm extrusion x3
* 20mm x 60mm extrusion, 140mm piece
* HTJ5 x8
* 500mm [https://discuss-assets.s3.amazonaws.com/original/2X/e/ed33b697e2f9506db156422f1d5dbcd73c923b3e.png MakerSlide]
* NEMA17 stepper motor
* Y motor mounting plate
* M3 washer x 4
* M3-6 x 4
* M5 extrusion nut x 2
* M5-8 x 2
* Y shaft support plate
* Flexible coupler
* Y axle tube
* SCCN8-6 shaft collar (4x)
* [http://www.ebay.com/itm/111557779094 608ZZ flanged bearing] (6x)
* GT2-20 pulley, 8mm bore (2x)
== Y pulley assembly ==
Everything x 2
* Y pulley plate
* 608ZZ flanged bearing
* M5-35 x 4
* M5-8 x 4
* M5-40 x 4
* M5 washer x 18
* M5 nut x 7
* M5 extrusion nut x 4
* Idler wheel subassembly x 4
* #16 aluminum spacer, 0.5″ x 4
* Y bearing plate
* 608ZZ flanged bearing
* SMBK5-30 spacer x 4
* Y idlers holder plate
== Y roller plates ==
* Y roller left plate
* M5-10 low head
* M5-20 x 2
* M5-25
* M5-30 x 2
* M5 washer x 17
* M5 nut x6
* [http://www.ebay.com/itm/271840910460 Eccentric spacer] x 2
* V-wheel subassembly x 4
* HBLSS5 bracket
*  Circular hook
*  M4 nut
*    M4 washer
*  M4 washer
*    M4 nut
*    #12 aluminum spacer, 0.625″
= TODO =
==Design==
* <s>Gantry back plate</s>
* <s>Gantry front plate</s>
* <s>PnP head lower plate</s>
* <s>PnP head middle plate</s>
* <s>PnP head nut mount plate</s>
* <s>PnP head top plate</s>
* <s>Shaft support plate</s>
* <s>X idlers plate</s>
* <s>X motor plate</s>
* <s>Y bearing plate</s>
* <s>Y idlers holder plate</s>
* <s>Y motor mount plate</s>
* <s>Y pulley side plate</s>
* <s>Y roller left plate</s>
* <s>Y roller right plate</s>
* <s>Z motor mount plate</s>
* <s>Align dragchain mounting points in z_motor_mount_plate and y_bar_right_roller</s>
* Mounting holes for dragchain
* Improve Y mounting points for plastic rather than metal (low priority)
=== Assemblies ===
* <s>Y-bar</s>
* <s>X idler plate</s>
* <s>x motor plate</s>
* <s>Y bar left roller plate</s>
* <s>Y bar right roller plate</s>
* <s>Gantry front plate</s>
* <s>Gantry back plate</s>
* <s>z motor plate</s>
* <s>Gantry</s>
* <s>x frame</s>
==Print==
* <s>Gantry front plate</s>
* <s>Gantry back plate</s>
* <s>PnP head nut mount plate</s>
* <s>PnP head top plate</s>
* <s>PnP head middle plate</s>
* <s>PnP head lower plate</s>
* <s>2x Y bearing plate</s>
* <s>2x Y idlers holder plate</s>
* <s>2x Y motor mount plate</s>
* <s>2x Y pulley side plate</s>
* <s>Y roller left plate</s>
* <s>Y roller right plate</s>
* <s>Z motor mount plate</s>
* <s>Shaft support plate</s>
* <s>X idlers plate</s>
* <s>x motor plate</s>
==Tasks==
* <s>Assemble main frame</s>
* <s>Assemble base</s>
* <s>Assemble machine housing</s>
* <s>Program RAMPS firmware</s>
* <s>Replace crimp connections of end-stop connectors with soldered connections</s>
** Calibrate RAMPS steps/mm all three axes
** Set traverse limits in firmware
* Attach frame to base
* Mount undercamera
* Tighten everything
* Complete vacuum/valve control
* Configure software for RAMPS
* Test place some pieces
* Test a board


= Resources =
= Resources =


Design files:
* Design files: https://git.nurd.space/parallax/picknplacer.git
https://git.nurd.space/parallax/picknplacer.git
* http://store.amberspyglass.co.uk/ <- Makerslide source
http://www.ebay.com/bhp/1ml-syringe
* http://www.ebay.com/bhp/1ml-syringe


= Printable parts =
= Part images =
*
<gallery>
Image:pnp_x_frame_assy.png
Image:pnp_y_bar_assy.png
Image:pnp_gantry_assy.png
Image:pnp_z_motor_mount_plate_assy.png
Image:pnp_y_bar_right_roller_plate_assy.png
Image:pnp_y_bar_left_roller_plate_assy.png
Image:pnp_x_motor_plate_assy.png
Image:pnp_x_idlers_plate_assy.png
Image:pnp_PNP_head_assy.png
Image:pnp_z_motor_mount_plate.png
Image:pnp_Y_roller_right_plate.png
Image:pnp_Y_roller_left_plate.png
Image:pnp_Y_pulley_side_plate.png
Image:pnp_Y_motor_mount_plate.png
Image:pnp_Y_idlers_holder_plate.png
Image:pnp_Y_bearing_plate.png
Image:pnp_x_motor_plate.png
Image:pnp_x_idlers_plate.png
Image:pnp_shaft_support_plate.png
Image:pnp_PNP_head_top_plate.png
Image:pnp_PNP_head_nut_mount_plate.png
Image:pnp_PNP_head_middle_plate.png
Image:pnp_PNP_head_lower_plate.png
Image:pnp_makerslide_750mm.png
Image:pnp_makerslide_500mm.png
Image:pnp_makerslide_250mm.png
Image:pnp_idler_wheel.png
Image:pnp_HBLTSW5.png
Image:pnp_Gantry_front_plate.png
Image:pnp_gantry_back_plate.png
Image:pnp_extrusions.png
Image:pnp_20x60x140_extrusion.png
Image:pnp_20x20x767_extrusion.png
Image:pnp_20x20x53_extrusion.png
Image:pnp_20x20x140_extrusion.png


</gallery>


= Pnp marlin driver specific config =


<pre>
<driver class="org.openpnp.machine.reference.driver.MarlinDriver" port-name="/dev/ttyACM0" baud="115200" feed-rate-mm-per-minute="5000.0">
        <pick-gcode>M106 S255</pick-gcode>
        <place-gcode>M107</place-gcode>
        <actuator-on-gcode>M8</actuator-on-gcode>
        <actuator-off-gcode>M9</actuator-off-gcode>
        <enable-gcode>M17</enable-gcode>
        <disable-gcode>M18</disable-gcode>
      </driver>
</pre>
= Ramps, yo =
[http://www.reprap.org/mediawiki/images/thumb/8/81/RAMPS_1.4.2.jpg/800px-RAMPS_1.4.2.jpg Ramps board layout]
== Wiring ==
* Pump red: D9+
* Pump black: D9-
* Solenoid green: D10+
* Solenoid brown: D10-
= Special GCode =
* Pump on: M42 P9 S255
* Pump off: M42 P9 S0
* Open Solenoid: M42 P10 S255
* Close solenoid: M42 P10 S0
= Misc info =
* A clone of the codebase is cloned into /home/common/picknplacer @printer-desktop for easy access when printing


= Todo =
= Todo =
* Create picture of RAMPS 1.4 connection scheme for PnP

Latest revision as of 16:46, 20 October 2016

Pick&placer
Picknplace-20160626.png
Participants
Skills Electronics, Mechanics, 3D Printing, Programming
Status Active
Niche Hardware
Purpose Instrument
Tool Yes
Location Nurdspace
Cost TBD
Tool category Fabrication

Pick&placer

Picknplace-20160626.png {{#if:Yes | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:Yes | [[Tool Cost::TBD | }}

Description

In 2015 we've made a ton of nurdnodes, which had been assembled by hand using a rudimentary tool. In order to produce many part prototypes, or make large productions runs, an automatic pick and place machine is imperative.

Design

Parts (unspecific)

makerslide xlots 0.02 EUR
HBLTSW5 brackets 5x ??
V-wheel ?x ??
603VV
screws?
T slot bolts
idler wheels
cameras x2 $13.05

PNP Head

PnP head middle plate x1
PnP head lower plate x1
Nema14 rotation stepper motor (14HM08-0504S) ? x1
M3-8 x 4
M3 washer x 14
M3 nut x 5
M3x6 x 5
M3 extrusion nut x 2
M3-20 x2
M4 nut (not M3) x?
M5-12 bolt x 2
M5 washer x 11
M5 nut x 2
M5-8 x?
M5-10 bolt x 2
M5 extrusion nut x 3
HTJ5 screw x 2
* linear flanged bearing
HBLSD5 bracket ? x 1
HBLSS5 bracket ? ?? x1
MakerSlide 250mm
Pick-up tube x1
M8 nylon washer x 3
GT2-36 pulley x1
GT2-60 belt loop x1
SCCN8-6 collar x 1
spring x1
Omron D3V-162-1C4 limit switch 2x
WSSB12-3-1 washer 1x
Flat spring 1x

X frame

Parts

  • 20x20x767 alu extrusion
  • M5-10
  • M5 washer x 10
  • M5-15 x 2
  • M5 nut x 3
  • M5-12
  • M5 extrusion nut
  • HBLSS5 bracket x2
  • 140mm extrusion x3
  • 20mm x 60mm extrusion, 140mm piece
  • HTJ5 x8
  • 500mm MakerSlide
  • NEMA17 stepper motor
  • Y motor mounting plate
  • M3 washer x 4
  • M3-6 x 4
  • M5 extrusion nut x 2
  • M5-8 x 2
  • Y shaft support plate
  • Flexible coupler
  • Y axle tube
  • SCCN8-6 shaft collar (4x)
  • 608ZZ flanged bearing (6x)
  • GT2-20 pulley, 8mm bore (2x)

Y pulley assembly

Everything x 2


  • Y pulley plate
  • 608ZZ flanged bearing
  • M5-35 x 4
  • M5-8 x 4
  • M5-40 x 4
  • M5 washer x 18
  • M5 nut x 7
  • M5 extrusion nut x 4
  • Idler wheel subassembly x 4
  • #16 aluminum spacer, 0.5″ x 4
  • Y bearing plate
  • 608ZZ flanged bearing
  • SMBK5-30 spacer x 4
  • Y idlers holder plate

Y roller plates

  • Y roller left plate
  • M5-10 low head
  • M5-20 x 2
  • M5-25
  • M5-30 x 2
  • M5 washer x 17
  • M5 nut x6
  • Eccentric spacer x 2
  • V-wheel subassembly x 4
  • HBLSS5 bracket
  • Circular hook
  • M4 nut
  • M4 washer
  • M4 washer
  • M4 nut
  • #12 aluminum spacer, 0.625″

TODO

Design

  • Gantry back plate
  • Gantry front plate
  • PnP head lower plate
  • PnP head middle plate
  • PnP head nut mount plate
  • PnP head top plate
  • Shaft support plate
  • X idlers plate
  • X motor plate
  • Y bearing plate
  • Y idlers holder plate
  • Y motor mount plate
  • Y pulley side plate
  • Y roller left plate
  • Y roller right plate
  • Z motor mount plate
  • Align dragchain mounting points in z_motor_mount_plate and y_bar_right_roller
  • Mounting holes for dragchain
  • Improve Y mounting points for plastic rather than metal (low priority)


Assemblies

  • Y-bar
  • X idler plate
  • x motor plate
  • Y bar left roller plate
  • Y bar right roller plate
  • Gantry front plate
  • Gantry back plate
  • z motor plate
  • Gantry
  • x frame

Print

  • Gantry front plate
  • Gantry back plate
  • PnP head nut mount plate
  • PnP head top plate
  • PnP head middle plate
  • PnP head lower plate
  • 2x Y bearing plate
  • 2x Y idlers holder plate
  • 2x Y motor mount plate
  • 2x Y pulley side plate
  • Y roller left plate
  • Y roller right plate
  • Z motor mount plate
  • Shaft support plate
  • X idlers plate
  • x motor plate

Tasks

  • Assemble main frame
  • Assemble base
  • Assemble machine housing
  • Program RAMPS firmware
  • Replace crimp connections of end-stop connectors with soldered connections
    • Calibrate RAMPS steps/mm all three axes
    • Set traverse limits in firmware
  • Attach frame to base
  • Mount undercamera
  • Tighten everything
  • Complete vacuum/valve control
  • Configure software for RAMPS
  • Test place some pieces
  • Test a board

Resources

Part images

  • Pnp x frame assy.png
  • Pnp y bar assy.png
  • Pnp gantry assy.png
  • Pnp z motor mount plate assy.png
  • Pnp y bar right roller plate assy.png
  • Pnp y bar left roller plate assy.png
  • Pnp x motor plate assy.png
  • Pnp x idlers plate assy.png
  • Pnp PNP head assy.png
  • Pnp z motor mount plate.png
  • Pnp Y roller right plate.png
  • Pnp Y roller left plate.png
  • Pnp Y pulley side plate.png
  • Pnp Y motor mount plate.png
  • Pnp Y idlers holder plate.png
  • Pnp Y bearing plate.png
  • Pnp x motor plate.png
  • Pnp x idlers plate.png
  • Pnp shaft support plate.png
  • Pnp PNP head top plate.png
  • Pnp PNP head nut mount plate.png
  • Pnp PNP head middle plate.png
  • Pnp PNP head lower plate.png
  • Pnp makerslide 750mm.png
  • Pnp makerslide 500mm.png
  • Pnp makerslide 250mm.png
  • Pnp idler wheel.png
  • Pnp HBLTSW5.png
  • Pnp Gantry front plate.png
  • Pnp gantry back plate.png
  • Pnp extrusions.png
  • Pnp 20x60x140 extrusion.png
  • Pnp 20x20x767 extrusion.png
  • Pnp 20x20x53 extrusion.png
  • Pnp 20x20x140 extrusion.png

Pnp marlin driver specific config

<driver class="org.openpnp.machine.reference.driver.MarlinDriver" port-name="/dev/ttyACM0" baud="115200" feed-rate-mm-per-minute="5000.0">
         <pick-gcode>M106 S255</pick-gcode>
         <place-gcode>M107</place-gcode>
         <actuator-on-gcode>M8</actuator-on-gcode>
         <actuator-off-gcode>M9</actuator-off-gcode>
         <enable-gcode>M17</enable-gcode>
         <disable-gcode>M18</disable-gcode>
      </driver>

Ramps, yo

Ramps board layout

Wiring

  • Pump red: D9+
  • Pump black: D9-
  • Solenoid green: D10+
  • Solenoid brown: D10-

Special GCode

  • Pump on: M42 P9 S255
  • Pump off: M42 P9 S0
  • Open Solenoid: M42 P10 S255
  • Close solenoid: M42 P10 S0

Misc info

  • A clone of the codebase is cloned into /home/common/picknplacer @printer-desktop for easy access when printing

Todo

  • Create picture of RAMPS 1.4 connection scheme for PnP
Retrieved from "https://nurdspace.nl/index.php?title=Picknplacer&oldid=7475"
Last modified
This page was last edited on 20 October 2016, at 16:46.