CoreAnet: Difference between revisions

From NURDspace
 
(19 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{Project
{{Project
|Name=CoreXYnetA6
|Name=CoreAnet
|Skills=Mechanics, reprap, 3D Printing,
|Skills=Mechanics, reprap, 3D Printing,
|Status=Planning
|Status=Planning
|Niche=Hardware
|Niche=Hardware
|Purpose=Tool
|Purpose=Tool
|Picture=Corexy-schematic.png
|Picture=Coreanet-casetest-forwiki.png
|Tool=No
|Tool=No
}}
}}
<gallery>
 
Dubious-anetA6.jpg
== Parts actually used ==
</gallery>
 
==== Frame ====
 
* 14x 469mm 30x60mm t-slot extrusion
* 8x 4020_Extrusion_Cap.stl scaled 150% to 6030 https://www.thingiverse.com/thing:4822278
* 36x 3030_corner_single.stl https://www.thingiverse.com/thing:2503636
* 72x slotnut M4 & M4x10-15 , not sure how long
 
 
* Some 1U 19" case for electronics, might change this
 
==== Z Axis ====
 
* 4x 380mm 8mm smooth rods
 
 
* 2x 340mm(??) TR8X8 leadscrews
* 2x flexcouplers (but i guess anything could work)
 
 
* 2x Z_Axis_Linear_Rail_Bracket_-_Left.stl https://www.thingiverse.com/thing:3268908
* 2x Z_Axis_Linear_Rail_Bracket_-_Right.stl https://www.thingiverse.com/thing:3268908
* 8x slotnut M4 & M4x10-15 , not sure how long
 
 
* 2x Z_Motor_Mount_1.0.stl https://www.thingiverse.com/thing:2254103
* 2x nema17 + some mounting screws
* 8x slotnut M4 & M4-10-15, not sure how long
 
 
* 2x Z_Axis_Linear_Rail_Bracket_-_Double_Z_-_Left.stl https://www.thingiverse.com/thing:3268908
* 2x Z_Axis_Linear_Rail_Bracket_-_Double_Z_-_Right.stl https://www.thingiverse.com/thing:3268908
* 8x slotnut M4 & M4x10-15 , not sure how long
 
==== XY Framemounted Axis ====
 
* 2x 400mm 8mm smooth rod
 
 
* 1x XY_Idler_Mount_-_Left_yDia8_-_1.1.stl https://www.thingiverse.com/thing:2254103
* 2x slotnut M4 & M4x10-15 , not sure how long
* 1x M3 about 35mm long?
* some M3 washers to space the bearings
* 4x F605ZZ bearings
 
 
* 1x XY_Idler_Mount_-_Right_yDia8_-_1.1.stl https://www.thingiverse.com/thing:2254103
* 2x slotnut M4 & M4x10-15 , not sure how long
* 1x M3 about 35mm long?
* some M3 washers to space the bearings
* 4x F605ZZ bearings
 
 
* 1x XY_Stepper_Mount_-_Left_yDia8_-_1.1.stl https://www.thingiverse.com/thing:2254103
* 3x slotnut M4 & M4x10-15 , not sure how long
* 1x nema17 + some mounting screws
* 1x timingbelt pulley + grubscrews
 
 
* 1x XY_Stepper_Mount_-_Right_yDia8_-_1.1.stl https://www.thingiverse.com/thing:2254103
* 3x slotnut M4 & M4x10-15 , not sure how long
* 1x nema17 + some mounting screws
* 1x GT2 16? 20? teeth timingbelt pulley + grubscrews
 
==== XY Moving Axis ====
 
* 2x ??mm 8mm smooth rods
 
 
* 2x Y_Carriage_Clamp_LM8UU_1.0.stl https://www.thingiverse.com/thing:2254103
* 2x Y_Carriage_xDia8_LM8UU_1.0.stl https://www.thingiverse.com/thing:2254103
* 8x M3x5x5 knurled brass heat-inserts
* 8x M3x10-maybe12 bolts
* 8x F605ZZ bearings
* some M3 to hold the bearings in place
 
 
* 1x X_Carriage_1.0.stl https://www.thingiverse.com/thing:2254103
* 2x LM8LUU bearings
* some M3x5x5 knurled brass heat-inserts
* some M3 bolts to hold stuff
 
 
* 4x Belt_Tensioner_1.0.stl https://www.thingiverse.com/thing:2254103
* 2x Belt_Clamp_1.0.stl https://www.thingiverse.com/thing:2254103
* 4x M3 bolts to tension the belts
 
 
* 2x long-ass GT2 belts (cut to size but never measured)
 
==== Extruder and Hotend and probe and ... ====
 
* 1x extrudermount-mod.stl https://www.thingiverse.com/thing:5775211
* 2x random 3mm rods i cut to ~12 mm
 
 
* 1x clone BMG https://www.tinytronics.nl/shop/en/3d-printing/extrusion/hotends-and-extruders/dual-drive-gear-extruder-1.75mm-bondtech-compatible
* 1x clone E3D https://www.tinytronics.nl/shop/en/3d-printing/extrusion/hotends-and-extruders/hotend-v6-direct-drive-1.75mm-0.4mm-e3d-compatible
* 1x half height nema17 17HS4023 https://aliexpress.com/item/1005001650755939.html
 
 
* 1x Euclid Probe https://euclidprobe.github.io/
* 1x BLTouch4HypercubeM3Nuts.stl https://github.com/nionio6915/Euclid_Probe/tree/main/stls/Mount%20Adapters/BLTouch
* 2x M3-10 and M3 nuts to mount it on BMG_mount
 
* 1x Duct_klaue_2.stl https://www.thingiverse.com/thing:4462678
 
==== Z Carriage ====
 
* 2x 300mm 30x30mm t-slot extrusion
* 2x 320mm 30x30mm t-slot extrusion
* 4x 3030_corner_single.stl https://www.thingiverse.com/thing:2503636
* 8x slotnut M4 & M4x10-15 , not sure how long
 
 
* 4x new-bed-mounts-just1mount.stl https://www.thingiverse.com/thing:5775256
* 8x slotnut M4 & M4x10-15 , not sure how long


== Why ==
== Why ==


Pokon gifted me a Anet A6 to remix. This page documents what i want to do with it.
Pokon gifted me a Anet A6 to remix. This page documents what i did with it.


== What ==
== What ==
<gallery>
Dubious-anetA6.jpg
Image:0_sketchedshape.png
Image:1_firsttwoscrews.jpg
Image:2_currentprintarea.png
Image:3_another9.jpg
Image:4_moarcorners.jpg
Image:5_moaaarcorners.jpg
Image:6_anet-parts-stripped.jpg
Image:7_sketch-with-220mm-bed.jpg
Image:8_framebuilding.jpg
Image:9_its-a-cube.jpg
Image:10_some-Z-parts.jpg
Image:11_more-Z-parts.jpg
Image:12_most-XY-parts.jpg
Image:13_custom-Z-parts.png
Image:14_Z-platform.jpg
Image:15_more-XY-parts.jpg
Image:16_Z-platform.jpg
Image:17_Z-platform-mods.jpg
Image:18_electronics.jpg
Image:19_lights.jpg
Image:20_bedsupport-sketch.jpg
Image:21_bedsupport.jpg
Image:22_bedsupports.jpg
Image:23_bedsupports.jpg
Image:24_extruder-and-hotend.jpg
</gallery>


I want to build a corexy printer and reach mad speeds. We have a pile of aluminium extrusion on which i want to base the frame.
I want to build a corexy printer and reach mad speeds. We have a pile of aluminium extrusion on which i want to base the frame.
Line 24: Line 170:
* do >200mm/s comfortably  
* do >200mm/s comfortably  
* be heavy
* be heavy
* require no parts i do not already have access to
* <s>require no parts i do not already have access to</s> failed, i caved
* <10 minute benchy!


== Wparts ==
== Wparts ==
Line 38: Line 185:
* 3x endstop switches with too short wires (but it comes with some 400mm extenders? hmm)
* 3x endstop switches with too short wires (but it comes with some 400mm extenders? hmm)
* 4x nema17 motors labelled HEM-17D3003
* 4x nema17 motors labelled HEM-17D3003
* 1x ''extruder'' , not sure what this is
* 1x ''extruder'' , not sure what this is (has two fans , 5150 for partcooling)
* linear bearings , 4x looks like a SC8UU or SCS8UU , 2x LM8LUU , 2x LMH8LUU
* linear bearings , 4x looks like a SC8UU or SCS8UU , 2x LM8LUU , 2x LMH8LUU
* 5015 radial fan
* 2x linear bearing ,


alloted :  
alloted :  
Line 51: Line 196:
* 2x 30x30 extrusion 483mm long
* 2x 30x30 extrusion 483mm long
* there's also some parts of 2020 extrusion somewhere
* there's also some parts of 2020 extrusion somewhere
bought specifically for it :
* brass heatinserts
* some bearings, belts
* e3d clone lite6
* bmg clone extruder


== Winspiration ==
== Winspiration ==
Line 57: Line 208:
* https://www.thingiverse.com/thing:2503636  - The BEST 3030 corners. Single and dual.
* https://www.thingiverse.com/thing:2503636  - The BEST 3030 corners. Single and dual.
* https://www.thingiverse.com/thing:3268908  - Hypercube Evolution Anet A8 Remix
* https://www.thingiverse.com/thing:3268908  - Hypercube Evolution Anet A8 Remix
* https://www.thingiverse.com/thing:3613857  - Bondtech BMG Direct for Hypercube Evolution -NO BRASS INSERT-
* https://www.thingiverse.com/thing:2617424  - Hypercube Evolution Complete Hotend Assembly
== Work ==
# Installed Raspbian https://www.raspberrypi.org/downloads/
# Installed klipper onto anet electronics and on raspbian https://github.com/KevinOConnor/klipper
# Added dwc2-for-klipper-socket https://github.com/Stephan3/dwc2-for-klipper-socket
# Installed rpi_ws281x for the leds https://github.com/jgarff/rpi_ws281x

Latest revision as of 00:33, 9 January 2023

CoreAnet
Coreanet-casetest-forwiki.png
Participants User:buzz
Skills Mechanics, reprap, 3D Printing
Status Planning
Niche Hardware
Purpose Tool
Tool No
Location
Cost
Tool category

CoreAnet

Coreanet-casetest-forwiki.png {{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost::{{{Cost}}} | }}


Parts actually used

Frame


  • Some 1U 19" case for electronics, might change this

Z Axis

  • 4x 380mm 8mm smooth rods


  • 2x 340mm(??) TR8X8 leadscrews
  • 2x flexcouplers (but i guess anything could work)




XY Framemounted Axis

  • 2x 400mm 8mm smooth rod


  • 1x XY_Idler_Mount_-_Left_yDia8_-_1.1.stl https://www.thingiverse.com/thing:2254103
  • 2x slotnut M4 & M4x10-15 , not sure how long
  • 1x M3 about 35mm long?
  • some M3 washers to space the bearings
  • 4x F605ZZ bearings


  • 1x XY_Idler_Mount_-_Right_yDia8_-_1.1.stl https://www.thingiverse.com/thing:2254103
  • 2x slotnut M4 & M4x10-15 , not sure how long
  • 1x M3 about 35mm long?
  • some M3 washers to space the bearings
  • 4x F605ZZ bearings



  • 1x XY_Stepper_Mount_-_Right_yDia8_-_1.1.stl https://www.thingiverse.com/thing:2254103
  • 3x slotnut M4 & M4x10-15 , not sure how long
  • 1x nema17 + some mounting screws
  • 1x GT2 16? 20? teeth timingbelt pulley + grubscrews

XY Moving Axis

  • 2x ??mm 8mm smooth rods





  • 2x long-ass GT2 belts (cut to size but never measured)

Extruder and Hotend and probe and ...



Z Carriage


Why

Pokon gifted me a Anet A6 to remix. This page documents what i did with it.

What

  • Dubious-anetA6.jpg
  • 0 sketchedshape.png
  • 1 firsttwoscrews.jpg
  • 2 currentprintarea.png
  • 3 another9.jpg
  • 4 moarcorners.jpg
  • 5 moaaarcorners.jpg
  • 6 anet-parts-stripped.jpg
  • 7 sketch-with-220mm-bed.jpg
  • 8 framebuilding.jpg
  • 9 its-a-cube.jpg
  • 10 some-Z-parts.jpg
  • 11 more-Z-parts.jpg
  • 12 most-XY-parts.jpg
  • 13 custom-Z-parts.png
  • 14 Z-platform.jpg
  • 15 more-XY-parts.jpg
  • 16 Z-platform.jpg
  • 17 Z-platform-mods.jpg
  • 18 electronics.jpg
  • 19 lights.jpg
  • 20 bedsupport-sketch.jpg
  • 21 bedsupport.jpg
  • 22 bedsupports.jpg
  • 23 bedsupports.jpg
  • 24 extruder-and-hotend.jpg

I want to build a corexy printer and reach mad speeds. We have a pile of aluminium extrusion on which i want to base the frame.

Wishes

  • do >200mm/s comfortably
  • be heavy
  • require no parts i do not already have access to failed, i caved
  • <10 minute benchy!

Wparts

from anet a6 :

  • aluminium heated bed 220x220x3mm
  • 12864 lcd and dubious electronics
  • T8 leadscrews (2x 318mm) 2x T8x8 nuts
  • M8 threaded rods (2x 400mm, 1x 150mm)
  • 8MM smooth rods (2x 418mm , 2x 380mm , 2x 340mm)
  • ~40 M3x18mm bolts and nuts
  • ~15 M4x8mm bolts
  • 3x endstop switches with too short wires (but it comes with some 400mm extenders? hmm)
  • 4x nema17 motors labelled HEM-17D3003
  • 1x extruder , not sure what this is (has two fans , 5150 for partcooling)
  • linear bearings , 4x looks like a SC8UU or SCS8UU , 2x LM8LUU , 2x LMH8LUU

alloted :

  • 12x 30x60 extrusion 469mm long

still to get a purpose :

  • 2x 30x60 extrusion 520mm long
  • 4x 30x30 extrusion 500mm long
  • 2x 30x30 extrusion 483mm long
  • there's also some parts of 2020 extrusion somewhere

bought specifically for it :

  • brass heatinserts
  • some bearings, belts
  • e3d clone lite6
  • bmg clone extruder

Winspiration

Work

  1. Installed Raspbian https://www.raspberrypi.org/downloads/
  2. Installed klipper onto anet electronics and on raspbian https://github.com/KevinOConnor/klipper
  3. Added dwc2-for-klipper-socket https://github.com/Stephan3/dwc2-for-klipper-socket
  4. Installed rpi_ws281x for the leds https://github.com/jgarff/rpi_ws281x
Retrieved from "https://nurdspace.nl/index.php?title=CoreAnet&oldid=13070"
Last modified
This page was last edited on 9 January 2023, at 00:33.