Latest revision as of 18:27, 5 August 2017

IMPORTANT: The content of this section is outdated. Please update this section if you can. If you have checked or updated this section and found the content to be suitable, please remove this notice.

Introduction

This is a beginning entry dedicated to the light setup in Diedenoort-NURDSpace. Original configuration: The three wall switches by the front door operate, from left to right: The ventilation The right-hand bank of lights (with back to door) including the 3 on the hook around the corner The left hand bank of lights

Current configuration

The left hand switch is for the single emergency light on the left closest to the door.
The right hand switch does nothing.
The fluorescent bulbs are connected together into 4 numbered groups:
1. The 6 in the dead centre of the space
2. The 2 over the printer desks (currently disabled)
3. The 3 over the desks at the far windows
4. The 5 closest to the door, on the near side of the I-beam, excluding the emergency light (only 2 of them are currently working).

These 4 channels are plugged into the lighting controller suspended in a white iron grid from the ceiling. This is plugged into a ceiling socket on a ? electrical group.

DMX

The DMX devices are controlled by the LanBox. DMX channels used:

Channels 1-6: node 0
Channels 7-12: node 1
Channels 13-18: node 2
Channels 19-24: node 3
Channels 25-30: node 4
Channels 31-36: node 5
Channels 37-42: node 6
Channels 43-48: node 7
Channels 49-54: node 8
Channels 55-60: node 9
Channels 61-66: node 10
Channels 67-72: node 11
Channels 73-78: node 12
Channels 79-84: node 13
Channels 85-90: node 14
Channels 91-96: node 15
Channel 241: showtec ch 1: fluorescent lights (do not dim!)
Channel 242: showtec ch 2: defused to prevent gnome attacks
Channel 243: showtec ch 3: fluorescent lights (do not dim!)
Channel 244: showtec ch 4: fluorescent lights (do not dim!)

Fluorescent lights schematic
- - 3 - -	- - 2 - -	- - 2 - -	(kitchen)
- - 3 - -	- - 1 - -	- - 1 - -	- - × - -	(living room)
- - 3 - -	- - 1 - -	- - 1 - -	- - 1 - -	- - 4 - -	- - 4 - -

The DMX cable is wired in the following sequence:

Lanbox
(5-->3 conversion)
ShowTec MultiDim MKII
a swarm of nodes
any termination? maybe? anyone?

Commands

The lights can be operated on #nurds using the following commands:

!ziza - Turn off TL tubes.
!aziz - Turn on TL tubes.

@@ Line 1: / Line 1: @@
+{{outdated}}
+= Introduction =
 This is a beginning entry dedicated to the light setup in Diedenoort-NURDSpace.
 Original configuration:
@@ Line 6: / Line 8: @@
 The left hand bank of lights
-Current configuration:
+= Current configuration =
-The left hand switch is for the single emergency light on the left closest to the door.
+* The left hand switch is for the single emergency light on the left closest to the door.
-The right hand switch does nothing.
+* The right hand switch does nothing.
-The fluorescent bulbs are connected together into 4 groups:
+* The fluorescent bulbs are connected together into 4 numbered groups:
-) The 6 in the dead centre of the space
+*# The 6 in the dead centre of the space
-) The 3 over the desks at the far windows
+*# The 2 over the printer desks (currently disabled)
-) The 2 over the printer desks
+*# The 3 over the desks at the far windows
-) The 5 closest to the door, on the near side of the I-beam, excluding the emergency light.
+*# The 5 closest to the door, on the near side of the I-beam, excluding the emergency light (only 2 of them are currently working).
 These 4 channels are plugged into the lighting controller suspended in a white iron grid from the ceiling. This is plugged into a ceiling socket on a ? electrical group.
-DMX
+= DMX =
-The DMX devices are currently configured as follows:
+The DMX devices are controlled by the [[LanBox]].  DMX channels used:
-Controller: Lanbox currently underneath the Lack by the yellow pipe.
+* Channels 1-6: node 0
-Channels 1-4: The small 4x controller on the desks at the far windows
+* Channels 7-12: node 1
-Channels 5-8: The strobe lamp
+* Channels 13-18: node 2
-Channels 9-12: The main fluorescent bulb controller
+* Channels 19-24: node 3
+* Channels 25-30: node 4
+* Channels 31-36: node 5
+* Channels 37-42: node 6
+* Channels 43-48: node 7
+* Channels 49-54: node 8
+* Channels 55-60: node 9
+* Channels 61-66: node 10
+* Channels 67-72: node 11
+* Channels 73-78: node 12
+* Channels 79-84: node 13
+* Channels 85-90: node 14
+* Channels 91-96: node 15
+* Channel 241: showtec ch 1: fluorescent lights (do not dim!)
+* Channel 242: showtec ch 2: defused to prevent gnome attacks
+* Channel 243: showtec ch 3: fluorescent lights (do not dim!)
+* Channel 244: showtec ch 4: fluorescent lights (do not dim!)
+{| class="wikitable" style="text-align: center;"
+|+ Fluorescent lights schematic
+|-
+| - - 3 - -
+| - - 2 - -
+| - - 2 - -
+| colspan=2 | (kitchen)
+|-
+| - - 3 - -
+| - - 1 - -
+| - - 1 - -
+| - - × - -
+|
+| colspan=2 | (living room)
+|-
+| - - 3 - -
+| - - 1 - -
+| - - 1 - -
+| - - 1 - -
+|
+| - - 4 - -
+| - - 4 - -
+|}
-Channels 32-34: The RGB LED lamp (1) on the top of the yellow pipe
-Channels 35-37: The RGB LED lamp (2) on the middle of the yellow pipe
-Channels 38-40: The RGB LED lamp (3) on the wall around the corner
-Channels 41-43: The RGB LED lamp (4) on the right on the pipes at the far windows
-Channels 44-46: The RGB LED lamp (5) on the left on the pipes at the far windows
-Channels 47-49: The RGB LED lamp (6) on the left hand wall.
 The DMX cable is wired in the following sequence:
-Lanbox
+* Lanbox
-Strobe
+* (5-->3 conversion)
-RGB1
+* [http://www.liquidx.nl/media/downloads/licht/Showtec%20MultiDim%20MKII%204-kan-5A%2050386.pdf ShowTec MultiDim MKII]
-RGB2
+* a swarm of nodes
-RGB3
+* any termination? maybe? anyone?
-(5-->3 conversion)
-(3-->5 conversion)
+= Commands =
-RGB4
+The lights can be operated on #nurds using the following commands:
-(5-->3 conversion)
+* !ziza - Turn off TL tubes.
-Small 4x controller
+* !aziz - Turn on TL tubes.
-Fluorescent controller
-(3-->5 conversion)
-RGB5
-RGB6
-A 120 ohm resistor is used as termination between pins 2 and 3.