No edit summary |
No edit summary |
||
Line 146: | Line 146: | ||
|} | |} | ||
[[Category: | [[Category:Radio]] |
Revision as of 15:56, 7 September 2024
IMPORTANT: The content of this section is outdated. Please update this section if you can. If you have checked or updated this section and found the content to be suitable, please remove this notice. |
Airplane Tracking | |
---|---|
Participants | Melan |
Skills | Linux, airplanes, radio, rtl-sdr |
Status | Active as fuck |
Niche | |
Purpose | Use for infra |
Tool | No |
Location | |
Cost | |
Tool category |
adsb_pi.jpg {{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost::{{{Cost}}} | }}
What
https://sdr-enthusiasts.gitbook.io/ads-b/useful-extras/managing-a-remote-station
An LXC running on Coherence (sdr.dhcp.nurd.space / 10.208.42.113) tracking airplanes, in total there are 3 RTL-SDR dongles connected while only one is being used for ADS-B. The other two remain available for any other SDR purposes. The ADSB decoder used is ReadSB some of the services are running under Docker. The setup is heavily based upon this guide [1].
The antenna is located above the bar under the skylight. As of right now, we are using a PCB-based 1090Mhz antennae, however, performance remains poor and a better antenna is very much desired.
mlat
I still want to see if we can improve mlat reception. Previously, when the project was running in a VM we barely did any mlat calculations being likely because the timing in the VM was off. After it was moved to an LXC container, mlat receptions improved. What I would love to experiment with is moving the receiver itself to an embedded device such as a Raspberry Pi instead, to see if this causes any sort of improvement in mlat calculations. This should be fairly simple as it only means we need to move readsb and possibly mlathub to physical hardware instead. A better antenna will very likely also improve our mlat reception.
How
Automatic Dependent Surveillance Broadcast (ADS-B) is a surveillance technology in which an aircraft determines its position via satellite navigation and periodically broadcasts it, enabling it to be tracked. The information can be received by air traffic control ground stations as a replacement for secondary surveillance radar, as no interrogation signal is needed from the ground. It can also be received by other aircraft to provide situational awareness and allow self-separation. ADS–B is "automatic" in that it requires no pilot or external input. It is "dependent" in that it depends on data from the aircraft's navigation system. This signal is transmitted at 1090Mhz and 978Mhz.
Hardware
Flightaware Pro Stick Plus
- Chip: R820T2
- Amplifier: 19dB with 0.4dB noise figure and OIP3 +39dB
- TCXO: 0.5 ppm
- Filter: 1,075 MHz to 1,105 MHz pass band with insertion loss of 2.3 dB; 30 dB attenuation on other frequencies
- Power Draw: 300 mA
- Weight: 17 g / 0.6 oz
- Dimensions: 95 mm x 32 mm x 13 mm
- Antenna Port: SMA female (requires SMA antenna cable and optionally N-male adapter for large antenna)
- Range: Over 300 nm/550 km depending on installation quality
- Performance: 10-20% more Mode S messages in installations where filtering is beneficial
Installed SDR dongles
Found 3 device(s): 0: Generic RTL2832U OEM 1: Generic RTL2832U 2: Generic RTL2832U OEM < IN USE 0: __________________________________________ Vendor ID: 0x0bda Product ID: 0x2838 Manufacturer: Realtek Product: RTL2838UHIDIR Serial number: 143.831 ppm Serial number enabled: yes IR endpoint enabled: yes Remote wakeup enabled: no __________________________________________ 1: __________________________________________ Vendor ID: 0x0bda Product ID: 0x2832 Manufacturer: Realtek Product: RTL2832U Serial number: flaw-ppm-0.939 Serial number enabled: yes IR endpoint enabled: no Remote wakeup enabled: no __________________________________________ 2: < IN USE __________________________________________ Vendor ID: 0x0bda Product ID: 0x2838 Manufacturer: Realtek Product: RTL2838UHIDIR Serial number: 1354980354 Serial number enabled: yes IR endpoint enabled: yes Remote wakeup enabled: no __________________________________________
Feeds
We currently are feeding to the following services
Name | Link |
---|---|
Adsbexchange | https://adsbx.org/sync/feeder.html?4A&Nurdspace |
Flightaware | https://uk.flightaware.com/adsb/stats/site/165985 |
Flightradar24 | https://www.flightradar24.com/account/feed-stats/?id=34863 |
Radarbox | https://www.radarbox.com/stations/EXTRPI015576 |
Planefinder | https://planefinder.net/coverage/receiver/228977 |
ADSBHub | https://www.adsbhub.org/statistic.php (@ space only) |
Opensky | https://opensky-network.org/receiver-profile?s=-1408232256 |
Piaware | |
Planewatch | Feeder 204 |
NurdSpace | https://alpha.radarvirtuel.com/stations/NURD |
feed.adsb.fi |
Ports
List of open ports, whom they belong to, and their function.
Port | Service | Description |
---|---|---|
80 | organizr | Handy dashboard that has easy access to the services |
8080 | Readsb | Webinterface |
8081 | Piaware | Piaware interface |
8082 | tar1090 | Improved Visualization |
8754 | fr24 | Fr24 feeder status |
8888 | Dozzle | Docker logs |
9000 | Portainer | Allow you to control Docker |
30001 | Readsb | TCP Raw Input |
30002 | Readsb | TCP Raw Output |
30003 | Readsb | TCP BaseStation Output |
30005 | Readsb | TCP Beast output |
30053 | Planefinder | Planefinder client |