Rubberduck (talk | contribs) (Created page with "{{Project |Name=Dell Equallogic Ps6000 recovery |Skills=Computers, |Status=Done |Niche=Infra |Purpose=Education |Tool=No |Location=@ home |Cost=0 |Category=Infra }} 1) Console...") |
Rubberduck (talk | contribs) No edit summary |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
|Name=Dell Equallogic Ps6000 recovery | |Name=Dell Equallogic Ps6000 recovery | ||
|Skills=Computers, | |Skills=Computers, | ||
|Status= | |Status=Active | ||
|Niche=Infra | |Niche=Infra | ||
|Purpose=Education | |Purpose=Education | ||
|Picture=/home/arko/Pictures/dell.png | |||
|Tool=No | |Tool=No | ||
|Location=@ home | |Location=@ home | ||
|Cost=0 | |Cost=0 | ||
|Category=Infra | |Category=Infra | ||
|Participants=Rubberduck | |||
}} | }} | ||
1) Console on the Equallogic and powercycle the device | 1) Console on the Equallogic and powercycle the device | ||
| Line 18: | Line 20: | ||
EQL> reload | EQL> reload | ||
And the defaults are back. | And the defaults are back. | ||
Launch Support Mode > support exec bash | |||
To enter a BASH shell > su exec bash | |||
Various “Netstat” and netstat_test commands…some of the most useful networking commands I’ve used so far: | |||
netstat -i | |||
nstat_test -p 0 | |||
nstat_test -r | |||
nstat_test -t | |||
“Cache Tool” | |||
cachetool | |||
Reveal NetBSD | |||
uname -a | |||
“RAIDTOOL” for displaying RAID Info, especially useful in watching the rebuilds with percentages | |||
raidtool | |||
Replication Tuning – TCP | |||
support repl-window-size | |||
Restart the Equallogic Management Service (Note: You must close and re-launch the Group Manager application after running these commands) | |||
eqlinit restart MgmtExec | |||
eqlinit restart-snap MgmtExec | |||
support eqlinit “restart MgmtExec” | |||
Check the status od the MgmtExec Service | |||
eqlinit status | |||
DOWN and UP ETH Ports … first select the Array that you want to operate on (the example connects to array JERMSMIT-01, then toggles eth0 off and then on again) | |||
member select JERMSMIT-01 | |||
eth select 0 down | |||
eth select 0 up | |||
“UNAME” (unsure what this is actually doing…) | |||
uname -a | |||
Restart the Network Management service | |||
eqlinit restart-snap netmgtd | |||
“PSGD Test” | |||
psgd_test -r | |||
“EQL Logger” | |||
eqllogger -r | |||
“Clear Cache” – The clearlostdata command will gather information about the state of this array for support and troubleshooting purposes. | |||
clearlostdata | |||
Latest revision as of 17:11, 17 October 2022
| Dell Equallogic Ps6000 recovery | |
|---|---|
| Participants | Rubberduck |
| Skills | Computers |
| Status | Active |
| Niche | Infra |
| Purpose | Education |
| Tool | No |
| Location | @ home |
| Cost | 0 |
| Tool category | Infra |
Dell Equallogic Ps6000 recovery
/home/arko/Pictures/dell.png {{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost::0 | }}
1) Console on the Equallogic and powercycle the device
2) Press CTRL+P on boot
3) Use the following commands: EQL> setenv RESETPASSWORD 1 EQL> reload And the defaults are back.
Launch Support Mode > support exec bash To enter a BASH shell > su exec bash
Various “Netstat” and netstat_test commands…some of the most useful networking commands I’ve used so far: netstat -i nstat_test -p 0 nstat_test -r nstat_test -t
“Cache Tool” cachetool
Reveal NetBSD uname -a
“RAIDTOOL” for displaying RAID Info, especially useful in watching the rebuilds with percentages raidtool
Replication Tuning – TCP support repl-window-size
Restart the Equallogic Management Service (Note: You must close and re-launch the Group Manager application after running these commands)
eqlinit restart MgmtExec eqlinit restart-snap MgmtExec support eqlinit “restart MgmtExec”
Check the status od the MgmtExec Service eqlinit status
DOWN and UP ETH Ports … first select the Array that you want to operate on (the example connects to array JERMSMIT-01, then toggles eth0 off and then on again) member select JERMSMIT-01 eth select 0 down eth select 0 up
“UNAME” (unsure what this is actually doing…) uname -a
Restart the Network Management service eqlinit restart-snap netmgtd
“PSGD Test” psgd_test -r
“EQL Logger” eqllogger -r
“Clear Cache” – The clearlostdata command will gather information about the state of this array for support and troubleshooting purposes. clearlostdata