| (8 intermediate revisions by 3 users not shown) | |||
| Line 9: | Line 9: | ||
}} | }} | ||
== What == | == What == | ||
OpenTherm gateway has been put between the heater and the thermostat. This way we are able to read the OpenTherm communication between them, and control the heater using the gateway. It is a board with a PIC controller that already came pre-flashed. It can be used with a FTDI cable or you can put an ESP8266 based NodeMCU board on it and communicate with that over Wifi. We went for the | OpenTherm gateway has been put between the heater and the thermostat. This way we are able to read the OpenTherm communication between them, and control the heater using the gateway. It is a board with a PIC controller that already came pre-flashed. It can be used with a FTDI cable or you can put an ESP8266 based NodeMCU board on it and communicate with that over Wifi. We first went for the ESP8266. The ESP8266 ran Espeasy with [https://www.letscontrolit.com/wiki/index.php/Ser2Net Ser2Net]. We later changed it with [https://www.nodo-shop.nl/nl/opentherm-gateway/207-ethernet-module-usr-tcp232-t2.html USR-TCP232-T2]. | ||
== Wiring == | == Wiring == | ||
Boiler: Remeha Calenta (http://www.archiproducts.com/en/products/revis/wall-mounted-condensation-boiler-remeha-calenta-25l_225443) | Boiler: Remeha Calenta (http://www.archiproducts.com/en/products/revis/wall-mounted-condensation-boiler-remeha-calenta-25l_225443) | ||
| Line 19: | Line 20: | ||
</gallery> | </gallery> | ||
== Integration with home assistant == | == Integration with home assistant == | ||
We | We do not use [https://github.com/jodur/py-otgw-mqtt py-otgw-mqtt] on [[Jarvis]] anymore but are using native OpenTherm support in Home Assistant. | ||
* IP: 10.208.1.43 | |||
* Host name: opentherm.lan.nurd.space | |||
* Port: 20108 | |||
For the CH return water temperature to be reported successfully the serial command AA=28 has been issued (http://otgw.tclcode.com/firmware.html#dataids). This command should persist in the OTGW and only be needed once. If however the return water temperature is once again missing and the Calenta is still used the command may be issued again. | |||
== Todo == | |||
* Update Remeha iSense thermostat firmware if possible | |||
* Get notified when water pressure is low | |||
== Links == | == Links == | ||
Latest revision as of 21:09, 7 April 2024
| OpenTherm Gateway | |
|---|---|
 | |
| Owner | The_Niz |
| Status | Infra |
| Location | Kitchen wall |
| Tool | Yes |
| Tool category | General |
Opentherm_spacegateway.jpg {{{InventoryOwner}}}Property "Tool Owner" (as page type) with input value "{{{InventoryOwner}}}" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process. Kitchen wall
What
OpenTherm gateway has been put between the heater and the thermostat. This way we are able to read the OpenTherm communication between them, and control the heater using the gateway. It is a board with a PIC controller that already came pre-flashed. It can be used with a FTDI cable or you can put an ESP8266 based NodeMCU board on it and communicate with that over Wifi. We first went for the ESP8266. The ESP8266 ran Espeasy with Ser2Net. We later changed it with USR-TCP232-T2.
Wiring
Boiler: Remeha Calenta (http://www.archiproducts.com/en/products/revis/wall-mounted-condensation-boiler-remeha-calenta-25l_225443)
Original wiring
Integration with home assistant
We do not use py-otgw-mqtt on Jarvis anymore but are using native OpenTherm support in Home Assistant.
- IP: 10.208.1.43
- Host name: opentherm.lan.nurd.space
- Port: 20108
For the CH return water temperature to be reported successfully the serial command AA=28 has been issued (http://otgw.tclcode.com/firmware.html#dataids). This command should persist in the OTGW and only be needed once. If however the return water temperature is once again missing and the Calenta is still used the command may be issued again.
Todo
- Update Remeha iSense thermostat firmware if possible
- Get notified when water pressure is low