(Created page with "{{Project |Name=FilaStrüdel |Skills=FilaStrüdeleling, |Status=Planning |Niche=Hardware |Purpose=Fun |Tool=No |Location=printer area |Cost=175 for the thing funded by members...") |
No edit summary |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 5: | Line 5: | ||
|Niche=Hardware | |Niche=Hardware | ||
|Purpose=Fun | |Purpose=Fun | ||
|Picture=Filastrudel.jpg | |||
|Tool=No | |Tool=No | ||
|Location= | |Location=door of the unused toilet | ||
|Cost=175 for the thing funded by members | |Cost=175 for the thing funded by members | ||
|Category=Fabrication | |Category=Fabrication | ||
}} | }} | ||
FilaStrüdel | = FilaStrüdel say what? = | ||
Well after years we got a filastruder for recycling filament to make new filament (filament-ception). | Well after years we got a filastruder for recycling filament to make new filament (filament-ception). | ||
Thanks for all the sponsors, you know who you are. | Thanks for all the sponsors, you know who you are. | ||
= Operating the filastruder = | |||
Manual: http://space.nurdspace.nl/~pokon/Filastruder%20Instructions_release_rev20d.pdf | |||
How it works: | How it works: | ||
I have no idea yet but will link the manual, it is | I have no idea yet but will link the manual, it is basically: | ||
Pallets go in (not whole wooden pallets but little plastic balls) | Pallets go in (not whole wooden pallets but little plastic balls) and will be heated to a melty temp so we get filament | ||
It will be automatically spooled with a motor and a spool | |||
after a fuckton of hours we have new filament to fuck up | after a fuckton of hours we have new filament to fuck up | ||
Temperature changes viscosity, and thus extrusion rate and diameter. This is one way of dialing in | |||
filament diameter. 10degC is about 0.10mm | |||
, increasing temperature will decrease filament diameter | |||
. That also means that the tighter the PID holds temperature, the better. | |||
Autotuning the PID is a good idea. | |||
Latest revision as of 11:03, 2 September 2017
| FilaStrüdel | |
|---|---|
 | |
| Participants | |
| Skills | FilaStrüdeleling |
| Status | Planning |
| Niche | Hardware |
| Purpose | Fun |
| Tool | No |
| Location | door of the unused toilet |
| Cost | 175 for the thing funded by members |
| Tool category | Fabrication |
Filastrudel.jpg {{#if:No | [[Tool Owner::{{{ProjectParticipants}}} | }} {{#if:No | [[Tool Cost::175 for the thing funded by members | }}
FilaStrüdel say what?
Well after years we got a filastruder for recycling filament to make new filament (filament-ception). Thanks for all the sponsors, you know who you are.
Operating the filastruder
Manual: http://space.nurdspace.nl/~pokon/Filastruder%20Instructions_release_rev20d.pdf How it works: I have no idea yet but will link the manual, it is basically:
Pallets go in (not whole wooden pallets but little plastic balls) and will be heated to a melty temp so we get filament
It will be automatically spooled with a motor and a spool
after a fuckton of hours we have new filament to fuck up
Temperature changes viscosity, and thus extrusion rate and diameter. This is one way of dialing in filament diameter. 10degC is about 0.10mm , increasing temperature will decrease filament diameter . That also means that the tighter the PID holds temperature, the better. Autotuning the PID is a good idea.