Revision as of 20:32, 30 April 2016

Lasercutter

Owner	Jglauche
Status	Untested
Tool	Yes
Tool category	Fabrication

Lasercutter

Jinan-lasercutter.jpg {{{InventoryOwner}}}Property "Tool Owner" (as page type) with input value "{{{InventoryOwner}}}" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process. {{{Location}}}Property "Tool Location" (as page type) with input value "{{{Location}}}" contains invalid characters or is incomplete and therefore can cause unexpected results during a query or annotation process.

Pew Laser

Specifications

Class IV
60x90 cm bed
90W CO2 Laser (dont run above ~70%)
Needs some love! (XP software currently MIA, electronics could get a good upgrade, needs calibration)
25 kg (lol) purified water
CW-3000 water chiller

Todo

~~Fill system with purified water (30 * 1L available)~~
~~Hook up chiller to cutter~~
Possibly recheck alignment (beam should be exact in the center of the mirror)
~~Realign the bed (z)~~
Solve exhaust fumes extraction problem
~~Arrange Co2 fire extinguisher in case of oopsies~~

Stuff to get

Hose for the exhaust (longer)

chaos chaotically ordered a PSU on 2016/04/27(or around) to replace the broken one ; http://www.aliexpress.com/snapshot/7615321008.html?orderId=74879451300975

Exhaust fumes extraction problem

Options:

Remove window above hallway door, replace with wood. mount pipe onto wood.
Cut hole in door, fit pipe over hole in door
Cut hole in air duct, mount pipe over hole

Decide on coarse filter, as the supplied filter will clog if use without.
Open door and toss out hose when in use. Revert when done.

Electrical problems

~~Get power to the other side of the room~~
~~Hook up ground~~ The machine's ground is wired internally to the euro socket, so no need for external ground.
- Unless there is no ground on the socket so when connecting the ground must be checked.

10/4 Laser cutter does not give output power anymore after first successful test run. no high frequent buzzing anymore one should expect. Only what appears the sounds of sparks on first fire. then nothing.

16/4 Opened up laser power supply (I know what I am doing) (famous last words) and it appears the flyback transformer is toast. the secondary of the transformer measures fully open. (or the resistance is >30 M Ohm)

Also the power supply appears to be a 80 W model whereas we have a 90W tube. Thoughts ?

2 options.

get new power supply. about €200 ish
get new flyback transformers and just hope it works. This is the cheaper option.

Power rating is 90W. Tube length is 120 cm.

link to manufacturer website

Manual

@@ Line 70: / Line 70: @@
 * [[File:help-chiller-3000.pdf]]
 * [http://wiki.nottinghack.org.uk/wiki/Laser_cutter/Inkscape Preparing content for lasercutter with Inkscape]
-= Old Discussion =
-Moeten we als nurdspace investeren in een LaserCutter en hoe gaan we dat betalen.
-== Money stuff ==
-=== What does running the cutter cost ===
-* Per hour use?
-* When does the tube die and how much does a new one cost?
- Cha0z: 60W CO2 Laser tube $150-$230 [http://www.aliexpress.com/wholesale?SearchText=co2+laser+tube+60w&catId=&initiative_id=SB_20140514065052 aliexpress]
- The0: plus 200$ shipment, and length&power are related so getting 60W in a 40W frame might be difficult
- The0: Life expectancy of a tube varies: between 1000 and 4000 hours. 1000 hours seems more realistic
- The0: So far the predominant failure mode I have heard people complain about seems to be mishandling:
-   Forgetting to switch on cooling, freezing of coolant during winter, and mechanical abuse.
-   Do we need to take stupidity into account?
- The0: lenses and mirrors deteriorate over time, especially if fume extraction is not working properly or
-   (output lens) if there is no air assist.
-   A lens will set you back about 40,-, a mirror about 20,-
-=== In favor of getting a cutter ===
-* zarya
-* The0
-* niz
-* FwD
-* buZz
-* Cha0z97
-* D2
-=== In favor of a fee per hour to amortize acquisition and running costs ===
-* The0
-* Cha0z
-* Zarya
-=== I want to *lend* money for a cutter ===
-* The0: up to 1000,-
-=== I want to donate monyz for a cutter ===
-* The0: 100,-
-* FwD: 100,-
-* buZz: 100,-
-* Cha0z97: 200,-
-* Fierman: 50,-
-* Niz: 100,-
-=== What can we sell to buy a cutter ===
-* The audio multi track recorder/mixer
-* <s>3x APC UPS</s> -> Sold for €200, which is now available.
-== Technical ==
-=== What do we want? ===
-* Size?
-** The0: 20x30 cm seems to be the smallest, 40x60 is one size up and considerably more expensive
-** The0: some cheap ebay engravers seem to support only 20x20, with variable reports of mechanical limitations (short axes) and software (irrelevant) causing this
-* Features?
-** Cha0z: Should be able to cut through 0.15mm steel to be able to produce SMT stencils.
-** Theo: motorized up/down and rotation axis (engraving round objects) would be neat.
-* Hardware?
-** The0: performance of software-only solution is horrible. while in theory they could achieve results extremely fast (with a fast computer), even the best software only solutions are rumoured to have difficulty cutting even paper. So, I, for one, am definitely in favor of a hardware solution,.but not definitely against some software-hardware combination.
-=== Where to get one ===
-* Ebay?
-** "cheap" 40W ebay lasers come in two varieties. The first (and cheapest at ~ 700 euro including shipment) variety has a fixed 20x30 (sometimes 20x20) cm platform and no air-assist. The second variety has a movable 40x60 cm platform, sometimes comes with a rotary attachment, has air-assist and costs ~2200 euro including shipment.
-The second variety has recently been banned from sales in the EU because of non-conformity (see last item on http://ec.europa.eu/consumers/safety/rapex/alerts/main/index.cfm?event=main.weeklyOverview&web_report_id=922). Curiously enough this ban has led to an enormous price increase for this type (now ~12000 euro). Possibly related to this, the EU outlets for the smaller variety seem to have shifted offices from Porthsmouth (UK) to Karlsruhe (DE), and several of these "German" sellers are now also offering spare lamps at ~170 euro + 20 euro shipment, which is quite competitive. Are they canabalizing non-conforming lasers and selling off the parts?
-* HPC Laser
-** http://hpclaser.co.uk/index.php?main_page=product_info&cPath=1&products_id=40 (but in need of electronic's change)
-The0: Buy cheapest ebay (~600,-), eventually replace controller (e.g. laoslaser.org), total budget ~1200,-
-The0: Mood swings. Cheap ebay requires upgrades to become marginally usable, and will forever be stuck with puny working area.
-The0: Aluminium t-nut profiles have become remarkably affordable recently. Add motors, pulleys, belts, nuts and bolts, and you have a XYZ robot. Then mount your choise of extruder/spindle or a laser head and mirrors and you have an ultimaker-ultra/CNC mill/lasercutter. Mount all and you have fireworks. Lets design a frame and put a price to it, so we can decide if this is feasible.
- buZz; [http://www.motedis.com/shop/Slot-profiles/Profile-30-B-Type-slot-8:::1_5.html motedis]
-bjornl: remcoo (tkkrlab) advised us to look at Lasersaur, an open source laser cutter: http://labs.nortd.com/lasersaur/ (Link is dead)